Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM

TOYOTA PARKING ASSIST-SENSOR SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK CLEARANCE WARNING ECU

E149991E16

  1. Disconnect the C25 clearance warning ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    C25-10 (IG) - Body ground
    L-R - Body ground
    IG power source circuit
    Ignition switch ON, back sonar or clearance sonar switch on
    11 to 14 V
    C25-10 (IG) - Body ground
    L-R - Body ground
    IG power source circuit
    Ignition switch ON, back sonar or clearance sonar switch off
    Below 1 V
    C25-21 (E) - Body ground
    W-B - Body ground
    Body ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the C25 ECU connector.



  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    C25-13 (RL) - Body ground
    R-W - Body ground
    Reverse position signal
    Ignition switch ON, shift lever moved to R
    7 V or higher
    C25-13 (RL) - Body ground
    R-W - Body ground
    Reverse position signal
    Ignition switch ON, shift lever moved to any position except R
    Below 1 V
    C25-12 (BBZ) - Body ground
    P-G - Body ground
    No. 1 clearance warning buzzer signal
    Sonar detects obstacle (buzzer sounds)
    Waveform 1
    C25-3 (SPD) - Body ground
    V-R - Body ground
    Vehicle speed signal
    Vehicle driven at approximately 20 km/h (12 mph)
    Waveform 2
    C25-22 (E2) - Body ground
    L - Body ground
    No. 1 ultrasonic sensor ground
    Always
    Below 1 V
    C25-24 (BOR) - C25-22 (E2)
    BR - L
    No. 1 ultrasonic sensor power source circuit
    Ignition switch ON, back sonar or clearance sonar switch on
    7.2 to 8.8 V
    C25-24 (BOR) - C25-22 (E2)
    BR - L
    No. 1 ultrasonic sensor power source circuit
    Ignition switch off
    Below 1.5 V
    C25-6 (SOR) - C25-22 (E2)
    P - L
    No. 1 ultrasonic sensor communication signal
    Ignition switch ON, back sonar or clearance sonar switch on
    Waveform 3
    If the result is not as specified, the ECU may have a malfunction.



      E171458E01
    1. Using an oscilloscope, check waveform 1.
      Measurement Condition 
      Item
      Content
      Terminal No. (Symbols)
      C25-12 (BBZ) - Body ground
      Tool Setting
      5 V/DIV., 1 msec./DIV.
      Condition
      Sonar detects obstacle (buzzer sounds)



    2. E169152E01
    3. Using an oscilloscope, check waveform 2.
      Measurement Condition 
      Item
      Content
      Terminal No. (Symbols)
      C25-3 (SPD) - Body ground
      Tool Setting
      5 V/DIV., 10 msec./DIV.
      Condition
      Vehicle driven at approximately 20 km/h (12 mph)



    4. E159890E01
    5. Using an oscilloscope, check waveform 3.
      Measurement Condition 
      Item
      Content
      Terminal No. (Symbols)
      C25-6 (SOR) - C25-22 (E2)
      Tool Setting
      2 V/DIV., 200 μsec./DIV.
      Condition
      Ignition switch ON, back sonar or clearance sonar switch on