FRONT POWER SEAT MOTOR ASSEMBLY (for Reclining) > REMOVAL |
| 1. REMOVE FRONT SEAT ASSEMBLY |
| 2. REMOVE RECLINING POWER SEAT SWITCH KNOB |
![]() |
Apply protective tape around the front seat cushion shield.
Using a screwdriver, detach the 2 claws and remove the reclining power seat switch knob.
| *1 | Protective Tape |
| 3. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB |
![]() |
Apply protective tape around the front seat cushion shield.
Using a screwdriver, detach the 4 claws and remove the slide and vertical power seat switch knob.
| *1 | Protective Tape |
| 4. REMOVE FRONT SEAT CUSHION SHIELD LH WITH FRONT INNER NO. 1 SEAT CUSHION SHIELD LH |
![]() |
Remove the 2 screws.
![]() |
Remove the 3 screws.
Detach the claw and guide.
Remove the front seat cushion shield LH with the front inner No. 1 seat cushion shield LH.
| 5. REMOVE FRONT SEAT INNER CUSHION SHIELD LH |
![]() |
Remove the screw.
Detach the claw and guide.
![]() |
Pull the front seat inner cushion shield LH to detach the claw and remove the front seat inner cushion shield LH.
| 6. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY (w/ Front Seat Side Airbag) |
![]() |
Detach the 4 front seat airbag wire harness clamps.
![]() |
Disconnect the No. 2 seat wire connector and detach the wire harness clamp.
![]() |
Remove the 2 screws, 4 bolts and separate type front seatback assembly.
| 7. REMOVE RECLINING ADJUSTER INSIDE COVER RH (w/ Front Seat Side Airbag) |
![]() |
Detach the guide and remove the reclining adjuster inside cover RH.
| 8. REMOVE RECLINING ADJUSTER INSIDE COVER LH (w/ Front Seat Side Airbag) |
![]() |
Detach the guide and remove the reclining adjuster inside cover LH.
| 9. REMOVE SEPARATE TYPE FRONT SEATBACK COVER |
![]() |
w/o Front Seat Side Airbag:
Disconnect the No. 2 seat wire connector and detach the wire harness clamp.
![]() |
Remove the hog rings from the wires of the separate type front seatback cover, and then roll up the separate type front seatback cover.
Pass the No. 2 seat wire through the hole of the separate type front seatback cover.
![]() |
Remove the hog rings and detach the strap of the separate type front seatback cover, and then roll up the separate type front seatback cover and No. 1 seatback cloth.
![]() |
Pass the strap of the separate type front seatback cover through the holes of the separate type front seatback pad.
![]() |
w/ Front Seat Side Airbag:
Remove the nut and detach the separate type front seatback cover bracket.
Remove the hog rings and roll up the separate type front seatback cover.

| *a | Front view of front seatback | *b | Rear view of front seatback |
![]() |
Detach the 4 claws and remove the 2 front seat headrest support assemblies and separate type front seatback cover from the separate type front seatback pad.
| 10. REMOVE SEPARATE TYPE FRONT SEATBACK PAD |
![]() |
Remove the separate type front seatback pad from the separate type front seatback spring assembly.
| 11. REMOVE NO. 1 SEATBACK CLOTH |
![]() |
Remove the No. 1 seatback cloth from the separate type front seatback spring assembly.
| 12. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Remove the screw.
Detach the claw and remove the reclining adjuster inside cover LH.
| 13. REMOVE RECLINING ADJUSTER INSIDE COVER LH (w/o Front Seat Side Airbag) |
![]() |
Remove the screw.
Detach the guide and remove the reclining adjuster inside cover LH.
| 14. REMOVE RECLINING ADJUSTER INSIDE COVER RH (w/ Front Seat Side Airbag) |
![]() |
Detach the guide and remove the reclining adjuster inside cover RH.
| 15. REMOVE NO. 2 SEAT WIRE (w/ Front Seat Side Airbag) |
![]() |
w/ Front Seat Side Airbag:
Disconnect the front power seat motor assembly (for Reclining) connector.
Detach the 2 wire harness clamps and remove the No. 2 seat wire.
| 16. REMOVE POWER SEAT MOTOR ASSEMBLY (for Reclining, w/o Front Seat Side Airbag) |
![]() |
Detach the 8 hooks and remove the seatback spring.
Disconnect the connector.
![]() |
Detach the 6 claws and remove the push nut from the reclining rod.
![]() |
Remove the reclining rod.
![]() |
Using a 4 mm socket hexagon wrench, remove the 3 bolts and power seat motor assembly (for Reclining).