Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

NAVIGATION SYSTEM > OPERATION CHECK



CHECK NAVIGATION SYSTEM NORMAL CONDITION
  1. If the cause of a symptom is any of the following, the corresponding symptom is normal; it is not a malfunction.

    Symptom
    Answer
    A longer route than expected is chosen.
    Depending on the road conditions, the navigation receiver assembly may determine that a longer route is quicker.
    Even when distance priority is high, the shortest route is not shown.
    Some routes may not be advised due to safety concerns.
    When the vehicle is put into motion immediately after the engine starts, the navigation system deviates from the correct position.
    If the vehicle starts before the navigation system activates, the system may not react.
    When driving on certain types of roads, especially new roads, the vehicle position deviates from the correct position.
    When the vehicle is driving on new roads not available on the SD card, the system attempts to match it to another nearby road, causing the position mark to deviate.



  2. I100066
  3. The following symptoms are not malfunctions, but are caused by errors inherent in the GPS, gyro sensor, speed sensor or navigation receiver assembly.

    1. The current position mark may be displayed on a nearby parallel road.



    2. I100067
    3. Immediately after a fork in the road, the current vehicle position mark may be displayed on the wrong road.



    4. I100068
    5. When the vehicle turns right or left at an intersection, the current vehicle position mark may be displayed on a nearby parallel road.



    6. I100069
    7. When the vehicle is carried, such as on a ferry, and the vehicle itself is not running, the current vehicle position mark may be displayed in the position where the vehicle was until a measurement can be performed by the GPS.



    8. I100070
    9. When the vehicle travels on a steep hill, the current vehicle position mark may deviate from the correct position.



    10. I100071
    11. When the vehicle makes a continuous turn (e.g. 360, 720, 1080 degrees), the current vehicle position mark may deviate from the correct position.



    12. I100072
    13. When the vehicle moves erratically, such as constant lane changes, the current vehicle position mark may deviate from the correct position.



    14. E106418
    15. When the ignition switch is turned to ACC or ON and the vehicle is turned on a turntable before parking, the current vehicle position mark may not indicate the correct direction. The same will occur when the vehicle comes out of the parking garage.



    16. I100074
    17. When the vehicle travels on a snowy road or a mountain path with tire chains installed or using a spare tire, the current vehicle position mark may deviate from the correct position.



    18. I100075
    19. When the tires are changed, the current vehicle position mark may deviate from the correct position.

      HINT:
      1. A change in tire diameter may cause a speed sensor error.
      2. Performing "tire change" in calibration mode will allow the system to correct the current vehicle position faster.


CHECK SD CARD

HINT:
Check the SD card installed into the navigation receiver assembly.

  1. Check whether the navigation screen is displayed when the "HOME" switch is pressed.

  2. If the navigation screen is not displayed, a warning message is displayed, and the navigation system continues to operate in audio mode, replace the SD card as the SD card is defective.


CHECK PANEL & STEERING SWITCH

HINT:
  1. The navigation receiver assembly panel switches and steering switches are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E273700
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E286750
  5. Select "Panel & Steering Switch" from the "Function Check/Setting" screen.



  6. E225786E01
  7. Panel & Steering Switch Check Mode
    Screen Description 
    Display
    Content
    *a: Switch condition
    1. "Pushed" is displayed when any switch is pushed
    2. If 2 or more switches are pushed at once, nothing is displayed
    *b: Number of switches pushed
    1. "1" is displayed when any switch is pushed
    2. If 2 or more switches are pushed at once, nothing is displayed
    *c: Rotary switch direction
    Direction of rotary switch is displayed

    1. Operate each switch and check that the switch conditions are correctly displayed.

      NOTICE:
      When the "MENU" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.


CHECK TOUCH SWITCH

HINT:
  1. The touch switches on the screen are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E273700
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E286751
  5. Select "Touch Switch" from the "Function Check/Setting" screen.



  6. Touch Switch Check



      E176521
    1. Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

      HINT:
      1. A "+" mark is displayed where the display is touched.
      2. The "+" mark remains on the display even after the finger is removed.


CHECK MIC & VOICE RECOGNITION

HINT:
  1. The microphone and microphone input level are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E273700
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E286752
  5. Select "Microphone Check" from the "Function Check/Setting" screen.



  6. E268457E01
  7. Microphone Check
    Screen Description 
    Display
    Content
    *a: Microphone input level meter
    Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.
    *b: Recording switch
    Starts recording.
    *c: Stop switch
    Stops recording and playing.
    *d: Play switch
    Plays the recorded voice.
    *e: Recording indicator
    Comes on while recording.

    1. When speaking into the microphone, check that the microphone input level meter changes according to the input level.

      HINT:
      The microphone is active at all times when this screen is displayed.

    2. Push the recording switch and perform voice recording.

      HINT:
      1. Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.
      2. While recording or playing, the switches other than the stop switch cannot be pushed.
      3. When no recording is present, the play switch cannot be pushed.
      4. Recording will stop after 5 seconds or when the stop switch is pushed.

    3. Check that the recording indicator remains on while recording and that the recording can be played normally.


CHECK GPS & VEHICLE SENSORS

HINT:
  1. GPS information, vehicle signals and sensor signals are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E273700
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E286753
  5. Select "System Sensors Check" from the "Function Check/Setting" screen.



  6. E273705E01
  7. System Sensor Check

    *a: GPS 
    Display
    Content
    Reception number
    Displays reception condition of the satellites used to determine vehicle position
    Blue: P (In use)
    System is using GPS signal for location.
    Yellow: T (Receiving)
    System is tracking GPS signal for location.
    No color: Not in use
    System cannot receive GPS signal. (Searching for GPS signal)
    Status
    Displays reception status of the satellites used to determine vehicle position
    OK (3D)
    3-dimensional location method is being used.
    OK (2D)
    2-dimensional location method is being used.
    NG
    Location data cannot be used.
    error
    Reception error has occurred.
    -
    Any other state.
    Measurement ratio
    Displays the ratio of satellites performing measurements
    3D
    The ratio of satellites performing 3D positioning is displayed.
    2D
    The ratio of satellites performing 2D positioning is displayed.
    NG
    The ratio of satellites not performing measurement is displayed.
    Date
    Date/time information obtained from GPS signals is displayed in Greenwich Mean Time (GMT).
    Position
    Latitude and longitude information on current position is displayed.

    *b: SPD 
    Display
    Content
    Pulse count
    Displays the accumulated number of input pulses beginning when this screen is displayed
    Speed
    Displays vehicle speed

    *c: Sensor Signal 
    Display
    Content
    Note
    Gyro Voltage
    Displays the output voltage of the gyro sensor
    -
    0 point Voltage
    Displays the zero-point voltage of the gyro sensor
    -
    Relative bearing
    Displays the output angle of the gyro sensor
    The amount of change in bearing angle (degrees) after the system sensor check screen is displayed (clockwise: "+", counterclockwise: "-").

    *d: Reset 
    Display
    Content
    Reset
    When this switch is pressed and held for 3 seconds or more, the values for display items of "Pulse Count" and "Relative bearing" are reset and display "0".

    *e: Gyro/Distance correction study situation 
    Display
    Content
    Gyro/Distance correction study situation
    Displays learning status of Gyro/Distance correction

    1. When the "System Sensors Check" screen is displayed, check all the sensor signals.

      HINT:
      This screen is updated once per second.



  8. E235422E01
  9. GPS Time Setting
    Screen Description 
    Display
    Content
    *a: Time display
    Displays the date and time in the device.
    *b: Time setting screen
    Setting is possible only when GPS signals are not being received.
    *c: Cursor movement switch
    Moves the cursor on the date and time setting screen to the right and left.
    *d: Adjustment switch
    Adjusts values of items selected by the cursor.
    *e: OK switch
    Selecting this switch after setting the date and time updates the date and time in the device (only when GPS signals are not received).

    1. When GPS signals are not being received, the data and time in the device can be adjusted.

      HINT:
      Time setting is possible only when GPS signals are not being received. When the navigation system is receiving GPS signals, priority is given to displaying the time and date received via GPS.


CHECK VEHICLE SIGNAL

HINT:
  1. Vehicle signals received by the navigation receiver assembly are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E273700
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E286754
  5. Select "Vehicle Signal" from the "Function Check/Setting I" screen.



  6. E281789
  7. Vehicle Signal Check Mode
    Screen Description 
    Display
    Content
    Battery
    Battery voltage is displayed.
    IG
    Ignition switch ON/OFF state is displayed.
    PKB
    Parking brake ON/OFF state is displayed.
    REV
    Reverse signal ON/OFF state is displayed.
    SPEED
    Vehicle speed is displayed in km/h.
    TAIL
    Tail signal (Light control switch) ON/OFF state is displayed.

    HINT:
    1. Only conditions have inputs are displayed.
    2. This screen displays vehicle signals input to the navigation receiver assembly.


    1. When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.


CHECK HANDS-FREE VOICE QUALITY AND VOLUME SETTING

NOTICE:
  1. Adjustment of the settings is required for each registered cellular phone.
  2. If no cellular phone has been registered, all switches cannot be selected.

HINT:
  1. The hands-free volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E273700
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E286755
  5. Select "HF Voice Quality Setting" from the "Function Check/Setting" screen.



  6. E273710E01
  7. Hands-Free Voice Quality Setting (Voice Quality Type adjustment)
    Screen Description 
    *a
    Numeric keypad
    *b
    Setting button
    *c
    Reset button

    1. If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.

    2. When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

      Settings 
      Parameter
      Target Phenomenon
      Voice Quality Type
      Positive Effect of Changing Voice Quality
      Negative Effect of Changing Voice Quality
      A
      (Noise)
      The other party hears background noise when listening to your voice.
      1000
      The amount of background noise the other party hears when listening to your voice is reduced.
      The volume of voice the other party hears when listening to your voice may temporarily drop.
      B
      (Noise)
      The other party hears a lot of background noise when listening to your voice.
      2000
      The amount of background noise the other party hears when listening to your voice is sharply reduced.
      The volume of voice the other party hears when listening to your voice may temporarily drop.
      C
      (Echo)
      The other party hears weak echoes.
      0100
      The amount of echo is reduced (low level).
      Sound quality of the other party deteriorates (low level).
      D
      (Echo)
      The other party hears strong echoes.
      0200
      The amount of echo is reduced (high level).
      Sound quality of the other party deteriorates (high level).

      Settings (When Multiple Phenomenon Occurred) 
      Parameter
      Target Phenomenon
      Voice Quality Type
      Positive Effect of Changing Voice Quality
      Negative Effect of Changing Voice Quality
      A+C
      The other party hears background noise and weak echoes when listening to your voice.
      1100
      1. The amount of background noise the other party hears when listening to your voice is reduced.
      2. The amount of echo is reduced (low level).
      1. The volume of voice may drop temporarily.
      2. Sound quality of the other party deteriorates (low level).
      A+D
      The other party hears background noise and strong echoes when listening to your voice.
      1200
      1. The amount of background noise the other party hears when listening to your voice is reduced.
      2. The amount of echo is reduced (high level).
      1. The volume of voice may drop temporarily.
      2. Sound quality of the other party deteriorates (high level).
      B+C
      The other party hears a lot of background noise and weak echoes when listening to your voice.
      2100
      1. The amount of background noise the other party hears when listening to your voice is sharply reduced.
      2. The amount of echo is reduced (low level).
      1. The volume of voice may drop temporarily.
      2. Sound quality of the other party deteriorates (low level).
      B+D
      The other party hears a lot of background noise and strong echoes when listening to your voice.
      2200
      1. The amount of background noise the other party hears when listening to your voice is sharply reduced.
      2. The amount of echo is reduced (high level).
      1. The volume of voice may drop temporarily.
      2. Sound quality of the other party deteriorates (high level).

      HINT:
      1. The default value is "0000".
      2. Settings will be applied when the setting button is selected.
      3. If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.
      4. If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.


CHECK DIGITAL TV RECEPTION

HINT:
  1. The reception condition of Digital TV (DTV) can be checked.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).



  2. E268454
  3. Select "Function Check/Setting" from the "Service Menu" screen.



  4. E286369
  5. Select "DTV reception check" from the "Function Check/Setting" screen.



  6. E273743E01
  7. DTV reception check
    Screen Description 
    Display
    Content
    *a: Up or down switch
    Enables the channel to be changed to the one to be checked.
    *b: Recheck/ STOP switch
    1. Recheck: Starts checking
    2. STOP: Stops checking
    *c: Digital TV tuner reception level check result
    Displays digital TV antenna reception levels as follows:
    1. 111 or more: Font color is black (good reception)
    2. 110 or less: Font color is red (poor reception)
    3. -: Not equipped with digital TV antenna
    *d: Antenna connection check
    Displays digital TV antenna connection status as follows:
    1. OK: Connected properly
    2. NG: Not connected properly
    3. -: Not equipped with digital TV antenna

    HINT:
    1. As digital TV is a terrestrial broadcast, the digital TV antenna cannot receive the signal in places where the signal may not reach the vehicle, such as mountains or tunnels.
    2. Even in areas where digital TV broadcasts for households can be received, the in-vehicle digital TV may not be able to receive the broadcast.


    1. Select the "Recheck" button to start the DTV reception check.

    2. Check the result displayed when the DTV reception check is complete.

      HINT:
      1. Do not depend solely on the reception level as a reference value as it may vary depending on the signal conditions such as wave interference.
      2. If the result changes after turning the vehicle around, it is not a malfunction, but is caused by a local weak electric field.
      3. If the reception level is abnormal, the antenna system or navigation receiver assembly is malfunctioning.


CHECK SPEAKER

HINT:
  1. This function is used when checking the speaker wiring and whether the speakers are functioning properly.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Turn audio mode on and play any audio source.

    HINT:
    This audio source will be used for the speaker check.

  2. Enter diagnostic mode (Click here).



  3. E268484
  4. Select "Failure Diagnosis" from the "Service Menu" screen.



  5. E281790
  6. Select "System Check" from the "Failure Diagnosis" screen.



  7. E273721
  8. Select "SP Check ON" from the "System Check Mode" screen.

  9. Check the speaker wiring and check that the speakers are functioning properly.

    HINT:
    1. Check that each speaker outputs sound from the selected audio source properly.
    2. "SP Check OFF" is displayed during the speaker check.
    3. Sound can be heard from the speakers around the vehicle in order beginning from the speaker on the front side.
    4. More than one speaker may sound simultaneously depending on the speaker wiring.

  10. Sound stops when any of the following conditions are met.

    1. The "SP Check OFF" switch is pressed.

    2. Ignition switch off.

    3. Diagnostic mode is turned off.

    4. The screen is changed to another screen.

    5. Audio mode is turned off.