DTC C1622 Open or Short Circuit in Back Camera Signal |
| DTC Code | DTC Detection Condition | Trouble Area |
| C1622 | Open or Short Circuit in rear television camera signal |
|

| 1.CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
| Result | Proceed to |
| No DTC is output | A |
| DTC is output | B |
|
| ||||
| A | ||
| ||
| 2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY) |
Disconnect the N6 navigation receiver assembly connector.
Disconnect the T38 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N6-7 (CA+) - T38-4 (CB+) | Always | Below 1 Ω |
| N6-8 (V+) - T38-2 (CV+) | Always | Below 1 Ω |
| N6-15 (CGND) - T38-3 (CGND) | Always | Below 1 Ω |
| N6-16 (V-) - T38-1 (CV-) | Always | Below 1 Ω |
| N6-7 (CA+) - Body ground | Always | 10 kΩ or higher |
| N6-8 (V+) - Body ground | Always | 10 kΩ or higher |
| N6-15 (CGND) - Body ground | Always | 10 kΩ or higher |
| N6-16 (V-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK NAVIGATION RECEIVER ASSEMBLY |
![]() |
Disconnect the N6 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| N6-15 (CGND) - Body ground | Always | Below 1 Ω |
| N6-16 (V-) - Body ground | Always | Below 1 Ω |
| *a | Component without harness connected (Navigation Receiver Assembly) |
|
| ||||
| OK | |
| 4.CHECK NAVIGATION RECEIVER ASSEMBLY |
![]() |
Disconnect the T38 rear television camera assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T38-4 (CB+) - T38-3 (CGND) | Ignition switch ON, shift lever in R | 5.5 to 7.05 V |
| *a | Front view of wire harness connector (to Rear Television Camera Assembly) |
|
| ||||
| OK | |
| 5.CHECK REAR TELEVISION CAMERA ASSEMBLY |
Using an oscilloscope, check the waveform.

| *a | Component with harness connected (Navigation Receiver Assembly) | *b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
| Item | Content |
| Tester Connection | N6-8(V+) - N6-16 (V-) |
| Tool Setting | 0.2 V/DIV., 50 μs/DIV. |
| Condition |
|
|
| ||||
| OK | ||
| ||
| 6.REPLACE REAR TELEVISION CAMERA ASSEMBLY |
Replace the rear television camera assembly with a new or normally functioning one (Click here).
| NEXT | |
| 7.CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
| Result | Proceed to |
| No DTC is output | A |
| DTC is output | B |
|
| ||||
| A | ||
| ||