Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM (for Navigation Receiver Type)

DTC    C1622    Open or Short Circuit in Back Camera Signal

for Preparation Click here


DESCRIPTION

This DTC is stored if the navigation receiver assembly judges as a result of its self check that the signals or signal lines between the navigation receiver assembly and the rear television camera assembly are not normal.

DTC Code
DTC Detection Condition
Trouble Area
C1622
Open or Short Circuit in rear television camera signal
  1. Harness or connector
  2. Rear television camera assembly
  3. Navigation receiver assembly

WIRING DIAGRAM


E224828E19


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTC is output
    B



B
Go to step 2
A

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the N11 navigation receiver assembly connector.

  1. Disconnect the T38 rear television camera assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N11-11 (CA+) - T38-4 (CB+)
    Always
    Below 1 Ω
    N11-12 (V+) - T38-2 (CV+)
    Always
    Below 1 Ω
    N11-23 (CGND) - T38-3 (CGND)
    Always
    Below 1 Ω
    N11-24 (V-) - T38-1 (CV-)
    Always
    Below 1 Ω
    N11-11 (CA+) - Body ground
    Always
    10 kΩ or higher
    N11-12 (V+) - Body ground
    Always
    10 kΩ or higher
    N11-23 (CGND) - Body ground
    Always
    10 kΩ or higher
    N11-24 (V-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT NAVIGATION RECEIVER ASSEMBLY


    E275624E11
  1. Disconnect the N11 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N11-23 (CGND) - Body ground
    Always
    Below 1 Ω
    N11-24 (V-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Navigation Receiver Assembly)



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


4.CHECK NAVIGATION RECEIVER ASSEMBLY


    E227664E28
  1. Disconnect the T38 rear television camera assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    T38-4 (CB+) - T38-3 (CGND)
    Ignition switch ACC
    5.5 to 7.05 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Television Camera Assembly)



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


5.CHECK REAR TELEVISION CAMERA ASSEMBLY


  1. Using an oscilloscope, check the waveform.


    E275625E17


    Text in Illustration 
    *a
    Component with harness connected
    (Navigation Receiver Assembly)
    *b
    Waveform 1
    *c
    Waveform 2
    *d
    Synchronized Signal
    *e
    Video Waveform
    -
    -
    Measurement Condition 
    Item
    Content
    Tester Connection
    N11-12 (V+) - N11-24 (V-)
    Tool Setting
    0.2 V/DIV., 50 μs/DIV.
    Condition
    1. Waveform 1: Ignition switch ON, shift lever in R
    2. Waveform 2: Ignition switch ON, shift lever in R, screen blacked out by covering camera lens

    OK:
    Waveform is as shown in illustration.

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.



NG
Go to step 6
OK

USE SIMULATION METHOD TO CHECK (Click here)  

6.REPLACE REAR TELEVISION CAMERA ASSEMBLY
  1. Replace the rear television camera assembly with a new or normally functioning one (Click here).


NEXT


7.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTC is output
    B



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
A

END (REAR TELEVISION CAMERA ASSEMBLY WAS DEFECTIVE)