Home › SECURITIES › THEFT DETERRENT › BLOCKING SYSTEM

BLOCKING SYSTEM > TERMINALS OF ECU



CHECK TELEPHONE TRANSCEIVER ASSEMBLY

B236628E02

  1. Disconnect the T31 telephone transceiver assembly connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T31-6 (IG2) - T31-9 (E)
    B-O - W-B
    Ignition switch
    Ignition switch ON
    11 to 14 V
    T31-9 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    T31-12 (+B) - T31-9 (E)
    L-Y - W-B
    Power supply
    Always
    11 to 14 V

  3. Reconnect the T31 telephone transceiver assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T31-1 (BLK1) - T31-9 (E)
    Y-B - W-B
    Transponder key ECU assembly output signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
    Pulse generation (See waveform 1)
    T31-2 (BLK4) - T31-9 (E)
    Y-G - W-B
    Transponder key ECU assembly input signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Pulse generation (See waveform 2)
    T31-7 (BLK2) - T31-9 (E)
    Y-B - W-B
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
    Pulse generation (See waveform 1)
    T31-8 (BLK3) - T31-9 (E)
    Y-G - W-B
    ECM output signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Pulse generation (See waveform 2)



  5. B241926E01
  6. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Tester Connection
    1. T31-1 (BLK1) - T31-9 (E)
    2. T31-7 (BLK2) - T31-9 (E)
    Tool Setting
    5 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.



  7. B069241E20
  8. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Tester Connection
    1. T31-2 (BLK4) - T31-9 (E)
    2. T31-8 (BLK3) - T31-9 (E)
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON


CHECK TRANSPONDER KEY ECU ASSEMBLY


    B276309E04
  1. Disconnect the T21 transponder key ECU assembly connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T21-1 (+B) - T21-16 (GND)
    L-Y - G
    Power supply
    Always
    11 to 14 V
    T21-2 (IG) - T21-16 (GND)
    B-O - G
    Ignition switch
    Ignition switch ON
    11 to 14 V
    T21-16 (GND) - Body ground
    G - Body ground
    Ground
    Always
    Below 1 Ω

  3. Reconnect the T21 transponder key ECU assembly connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T21-12 (EFII) - T21-16 (GND)
    Y-B - G
    Transponder key ECU assembly output signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
    Pulse generation (See waveform 1)
    T21-13 (EFIO) - T21-16 (GND)
    Y-G - G
    Transponder key ECU assembly input signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Pulse generation (See waveform 2)



  5. B241926E01
  6. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Tester Connection
    T21-12 (EFII) - T21-16 (GND)
    Tool Setting
    5 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.



  7. B069241E20
  8. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Tester Connection
    T21-13 (EFIO) - T21-16 (GND)
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON


CHECK ECM (for 1KD-FTV [except i-ART])

B236632E02

  1. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E5-29 (IMO) - Body ground
    Y-B - Body ground
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
    Pulse generation (See waveform 1)
    E5-30 (IMI) - Body ground
    Y-G - Body ground
    ECM output signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Pulse generation (See waveform 2)



  2. B241926E01
  3. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Tester Connection
    E5-29 (IMO) - Body ground
    Tool Setting
    5 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.



  4. B069241E20
  5. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Tester Connection
    E5-30 (IMI) - Body ground
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON


CHECK ECM (for 2TR-FE)

B121958E11

  1. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E9-15 (IMO) - Body ground
    Y-B - Body ground
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
    Pulse generation (See waveform 1)
    E9-16 (IMI) - Body ground
    Y-G - Body ground
    ECM output signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Pulse generation (See waveform 2)



  2. B241926E01
  3. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Tester Connection
    E9-15 (IMO) - Body ground
    Tool Setting
    5 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.



  4. B069241E20
  5. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Tester Connection
    E9-16 (IMI) - Body ground
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON


CHECK ECM (for 1GR-FE)

G036662E32

  1. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E13-15 (IMO) - Body ground
    Y-B - Body ground
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
    Pulse generation (See waveform 1)
    E13-16 (IMI) - Body ground
    Y-G - Body ground
    ECM output signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Pulse generation (See waveform 2)



  2. B241926E01
  3. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Tester Connection
    E13-15 (IMO) - Body ground
    Tool Setting
    5 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.



  4. B069241E20
  5. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Tester Connection
    E13-16 (IMI) - Body ground
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON


CHECK ECM (for 2TR-FBE)

B286952E03

  1. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E25-32 (IMO) - Body ground
    Y-B - Body ground
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
    Pulse generation (See waveform 1)
    E25-31 (IMI) - Body ground
    Y-G - Body ground
    ECM output signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Pulse generation (See waveform 2)



  2. B241926E01
  3. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Tester Connection
    E25-32 (IMO) - Body ground
    Tool Setting
    5 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.



  4. B069241E20
  5. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Tester Connection
    E25-31 (IMI) - Body ground
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON


CHECK ECM (for 1KD-FTV [for i-ART])

B286952E04

  1. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E31-29 (IMO) - Body ground
    Y-B - Body ground
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.
    Pulse generation (See waveform 1)
    E31-28 (IMI) - Body ground
    Y-G - Body ground
    ECM output signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    Pulse generation (See waveform 2)



  2. B241926E01
  3. Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Tester Connection
    E31-29 (IMO) - Body ground
    Tool Setting
    5 V/DIV., 500 ms./DIV.
    Condition
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned ON after battery disconnected and connected.



  4. B069241E20
  5. Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Tester Connection
    E31-28 (IMI) - Body ground
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON