Home › SECURITIES › THEFT DETERRENT › BLOCKING SYSTEM

DTC    B1573    Short in Telephone Antenna Circuit

DTC    B15CB    Telematics Transceiver Antenna Disconnected


DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna (telephone antenna) circuit.

DTC Code
DTC Detection Condition
Trouble Area
B1573
There is a short circuit in the navigation antenna assembly (telephone antenna) between the telephone transceiver and instrument panel integration antenna assembly, or at the points where it connects to the telephone transceiver and instrument panel integration antenna assembly.
  1. Telephone transceiver assembly
  2. Instrument panel integration antenna assembly (telephone antenna)
  3. Harness or connector
B15CB
There is an open circuit in the navigation antenna assembly (telephone antenna) between the telephone transceiver and instrument panel integration antenna assembly, or at the points where it connects to the telephone transceiver and instrument panel integration antenna assembly.

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the telephone transceiver, instrument panel integration antenna assembly and/or navigation antenna assembly (telephone antenna), refer to the Service Bulletin.
  2. When the telephone transceiver is replaced, it is necessary to set the contract mode.

1.CHECK CONNECTION OF CONNECTOR
  1. Turn the ignition switch off.

  1. Check that the connectors are properly connected to the telephone transceiver, instrument panel integration antenna assembly and navigation antenna assembly (telephone antenna).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTOR CORRECTLY
OK


2.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


3.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B1573 or B15CB is not output.



NG
Go to step 4
OK

END 

4.CHECK CONNECTOR CONDITION
  1. Disconnect the navigation antenna assembly (telephone antenna) connector [color: wine red].

  1. Check that the connector pins are not bent.

    OK:
    Connector pins are not bent.



NG
REPAIR OR REPLACE NAVIGATION ANTENNA ASSEMBLY
OK


5.CHECK INSTRUMENT PANEL INTEGRATION ANTENNA ASSEMBLY (TELEPHONE ANTENNA)


    B330385E01
  1. Disconnect the instrument panel integration antenna assembly (telephone antenna) connector [color: wine red].

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Core wire - Shield
    Always
    4 to 11 kΩ

    Text in Illustration 
    *1
    Core wire
    *2
    Shield



NG
REPLACE INSTRUMENT PANEL INTEGRATION ANTENNA ASSEMBLY (TELEPHONE ANTENNA)
OK


6.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


7.CHECK FOR DTC
  1. Wiggle the navigation antenna assembly (telephone antenna).

  1. Check for the DTCs (Click here).

    OK:
    DTC B1573 or B15CB is not output.



NG
Go to step 8
OK

END 

8.REPLACE INSTRUMENT PANEL INTEGRATION ANTENNA ASSEMBLY
  1. Temporarily replace the instrument panel integration antenna assembly with a new or normally functioning one.


NEXT


9.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


10.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B1573 or B15CB is not output.



NG
Go to step 11
OK

END (INSTRUMENT PANEL INTEGRATION ANTENNA IS DEFECTIVE) 

11.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
  1. Temporarily replace the telephone transceiver assembly with a new or normally functioning one (Refer to the Service Bulletin).


NEXT


12.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


13.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B1573 or B15CB is not output.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

END (TELEPHONE TRANSCEIVER ASSEMBLY IS DEFECTIVE)