FUEL INJECTOR (w/ Glow Plug Controller) > INSTALLATION |
| 1. INSTALL INJECTOR ASSEMBLY |
![]() |
Install 4 new injection nozzle seats to the cylinder head.
Apply a small amount of clean engine oil to 4 new O-rings.
![]() |
Install one of the O-rings to each injector as shown in the illustration.
| *1 | New O-Ring |
Insert the 4 injectors into the cylinder head.
![]() |
Temporarily install 4 new washers and the 4 No. 1 nozzle holder clamps with the 4 bolts.
| *1 | New Washer |
| *a | Downward |
![]() |
| *1 | No. 1 Nozzle Holder Clamp |
Temporarily install the 4 injection pipes with the union nuts.
![]() |
Check the nozzle leakage pipe. Check that there are no scratches or dents on the 5 union seal surfaces.
If scratches or dents are present, replace the nozzle leakage pipe.
![]() |
Set the nozzle leakage pipe and 5 new gaskets in place.
| *1 | Union Bolt |
| *2 | Injector Hollow Screw |
| *3 | New Gasket |
Apply a small amount of oil to the 4 injector hollow screws and union bolt.
Temporarily install the nozzle leakage pipe with the 4 injector hollow screws and union bolt.
Tighten the 4 nozzle holder clamp bolts.
Remove the 4 injection pipes.
![]() |
Tighten the 4 injector hollow screws in order from 1 to 4.
| *1 | Union Bolt |
Tighten the union bolt.
| 2. INSPECT FOR FUEL LEAK |
![]() |
Check that there are no leaks from the nozzle leakage pipe connection.
Install a new gasket and the No. 2 nozzle leakage pipe to the cylinder head with SST (check valve).
Apply a small amount of soapy water (or other fluid for detecting fuel leakage) on the nozzle leakage pipe connection.
![]() |
Install SST (turbocharger pressure gauge) to the fuel return side of the nozzle leakage pipe, maintain 100 kPa (1.0 kgf/cm2, 15 psi) of pressure for 60 seconds and check that no bubbles form.
After checking for fuel leaks, wipe off the soapy water from the nozzle leakage pipe connection.
Remove SST, the No. 2 nozzle leakage pipe and gasket.
| 3. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Install 4 new No. 3 cylinder head cover gaskets to the cylinder head cover in the directions shown in the illustration.
| *1 | No. 3 Cylinder Head Cover Gasket |
| *2 | Cylinder Head Cover |
Remove any old seal packing (FIPG material) from the cylinder head.
![]() |
Apply seal packing to the areas shown in the illustration.
![]() | Seal Packing |
Install a new cylinder head cover gasket to the cylinder head cover.
![]() |
Temporarily install the cylinder head cover with the 10 bolts and 2 nuts in the order shown in the illustration. Then, tighten the 10 bolts and 2 nuts in the order shown in the illustration in 2 progressive steps.
Connect the ventilation hose.
Install 4 new nozzle holder seals.
| 4. INSTALL NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY |
Install the No. 2 cylinder head cover with the 3 bolts.
| 5. INSTALL WIRING HARNESS CLAMP BRACKET |
Install the 2 wiring harness clamp brackets with the 3 bolts.
Attach the 6 wire harness clamps.
| 6. INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY |
![]() |
Temporarily install the No. 2 nozzle leakage pipe with the 3 bolts.
![]() | Union Bolt |
Temporarily install a new gasket and the union bolt.
Tighten the 3 bolts and union bolt.
| 7. INSTALL NO. 3 NOZZLE LEAKAGE PIPE |
![]() |
Apply a light coat of fuel to the O-ring of the fuel check valve.
| *1 | O-Ring |
Temporarily install the No. 3 nozzle leakage pipe with the 2 bolts.
Temporarily install a new gasket and the fuel check valve.
Tighten the 2 bolts and fuel check valve.
Connect the 3 fuel hoses.
| 8. INSTALL NO. 2 FUEL PIPE |
![]() |
Apply a light coat of fuel to the O-ring of the fuel check valve.
| *1 | O-Ring |
Install a new gasket to the No. 2 fuel pipe and temporarily install the fuel check valve.
Temporarily install a new gasket and the supply pump hollow screw.
Using a 6 mm hexagon wrench, tighten the supply pump hollow screw.
Tighten the fuel check valve.
| 9. INSTALL WIRING HARNESS CLAMP BRACKET |
Install the wiring harness clamp bracket with the bolt.
Attach the wire harness clamp.
| 10. INSTALL NO. 4 INJECTION PIPE SUB-ASSEMBLY |
Temporarily install the No. 4 injection pipe with the union nuts.
Install the 2 No. 2 injection pipe clamps with the bolt and nut.
Using a 17 mm union nut wrench, tighten the injection pipe union nut on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.
| 11. INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER |
| 12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 13. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
![]() |
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's B line.
| Item | Specified Condition |
| A/T | 11.1 liters (11.7 US qts, 9.8 Imp. qts) |
| M/T | 9.8 liters (10.4 US qts, 8.6 Imp. qts) |
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
![]() |
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2,500 to 3,000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
After the coolant cools down, check that the coolant level is at the F line.
If the coolant level is below the F line, add TOYOTA SLLC to the F line.
| 14. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Check if the engine starts.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.*1
![]() |
Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak.*2
| *a | Reference (Active Test Operation) |
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine / DTC.
Read Current DTCs.
Clear the DTCs (Click here).
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine / DTC.
Read Current DTCs.
| 15. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17.1 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks.
If no external leaks are found, check the cylinder block and head.
| 16. INSPECT FOR FUEL LEAK |
Perform the Active Test.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine / Active Test.
Perform the Active Test.
| Intelligent Tester Display | Test Part | Control Range | Diagnostic Note |
| Test the Fuel Leak | Pressurize common rail interior and check for fuel leaks | Stop/Start |
|
| 17. INSPECT FOR OIL LEAK |
Start the engine. Make sure that there are no oil leaks from the areas that were worked on.
| 18. INSPECT ENGINE OIL LEVEL |
Warm up the engine, stop the engine and wait 5 minutes. The engine oil level should be between the dipstick low level mark and full level mark.
If low, check for leakage and add oil up to the full level mark.