COMMON RAIL (w/ Glow Plug Controller) > INSTALLATION |
| 1. INSTALL COMMON RAIL ASSEMBLY |
Install the common rail with the 2 bolts.
Connect the pressure discharge valve connector.
| 2. INSTALL VACUUM CONTROL VALVE SET |
![]() |
Install the vacuum control valve set with the 2 bolts.
| *1 | Paint Mark (White) |
| *2 | Paint Mark (Green) |
Connect the 3 vacuum hoses and 2 vacuum switching valve connectors.
| 3. INSTALL OIL FILTER SUB-ASSEMBLY |
Check and clean the oil filter installation surface.
Apply clean engine oil to the gasket of a new oil filter.
Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.
![]() |
Using SST, tighten the oil filter. Depending on the space available, choose from the following.
If enough space is available, use a torque wrench to tighten the oil filter.
If enough space is not available to use a torque wrench, tighten the oil filter 3/4 of a turn by hand or with a common wrench.
| 4. INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY |
![]() |
Temporarily install the No. 2 nozzle leakage pipe with the 3 bolts.
![]() | Union Bolt |
Temporarily install a new gasket and the union bolt.
Tighten the 3 bolts and union bolt.
| 5. INSTALL NO. 3 NOZZLE LEAKAGE PIPE |
![]() |
Apply a light coat of fuel to the O-ring of the fuel check valve.
| *1 | O-Ring |
Temporarily install the No. 3 nozzle leakage pipe with the 2 bolts.
Temporarily install a new gasket and the fuel check valve.
Tighten the 2 bolts and fuel check valve.
Connect the 3 fuel hoses.
| 6. INSTALL NO. 2 FUEL PIPE |
![]() |
Apply a light coat of fuel to the O-ring of the fuel check valve.
| *1 | O-Ring |
Install a new gasket to the No. 2 fuel pipe and temporarily install the fuel check valve.
Temporarily install a new gasket and the supply pump hollow screw.
Using a 6 mm hexagon wrench, tighten the supply pump hollow screw.
Tighten the fuel check valve.
| 7. INSTALL WIRING HARNESS CLAMP BRACKET |
Install the 2 wiring harness clamp brackets with the 3 bolts.
Attach the 6 wire harness clamps.
| 8. INSTALL NO. 4 INJECTION PIPE SUB-ASSEMBLY |
Temporarily install the No. 4 injection pipe with the union nuts.
Install the 2 No. 2 injection pipe clamps with the bolt and nut.
Using a 17 mm union nut wrench, tighten the injection pipe union nut on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.
| 9. INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER |
| 10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 11. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
![]() |
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's B line.
| Item | Specified Condition |
| A/T | 11.1 liters (11.7 US qts, 9.8 Imp. qts) |
| M/T | 9.8 liters (10.4 US qts, 8.6 Imp. qts) |
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
![]() |
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2,500 to 3,000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
After the coolant cools down, check that the coolant level is at the F line.
If the coolant level is below the F line, add TOYOTA SLLC to the F line.
| 12. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Check if the engine starts.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.*1
![]() |
Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak.*2
| *a | Reference (Active Test Operation) |
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine / DTC.
Read Current DTCs.
Clear the DTCs (Click here).
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine / DTC.
Read Current DTCs.
| 13. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17.1 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks.
If no external leaks are found, check the cylinder block and head.
| 14. INSPECT FOR FUEL LEAK |
Perform the Active Test.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine / Active Test.
Perform the Active Test.
| Intelligent Tester Display | Test Part | Control Range | Diagnostic Note |
| Test the Fuel Leak | Pressurize common rail interior and check for fuel leaks | Stop/Start |
|
| 15. INSPECT FOR OIL LEAK |
Start the engine. Make sure that there are no oil leaks from the areas that were worked on.
| 16. INSPECT ENGINE OIL LEVEL |
Warm up the engine, stop the engine and wait 5 minutes. The engine oil level should be between the dipstick low level mark and full level mark.
If low, check for leakage and add oil up to the full level mark.