DTC B15C3 Speaker Output Short |
| DTC Code | DTC Detection Condition | Trouble Area |
| B15C3 | A short is detected in the speaker output circuit. |
|

| 1.CHECK FOR DTC |
Disconnect the R20 and R19 radio and display receiver assembly connectors.
Clear the DTC (Click here).
Check if DTC B15C3 is output.
|
| ||||
| OK | |
| 2.CHECK FOR DTC |
Reconnect the R19 radio and display receiver assembly connector.
Clear the DTC (Click here).
Check if DTC B15C3 is output.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - FRONT NO. 2 SPEAKER) |
Disconnect the R20 radio and display receiver assembly connector.
Disconnect the T25*1 and/or T24*2 front No. 2 speaker connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R20-1 (FR+) - T25-4 | Always | Below 1 Ω |
| R20-5 (FR-) - T25-2 | ||
| R20-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| R20-5 (FR-) - Body ground |
| Tester Connection | Condition | Specified Condition |
| R20-2 (FL+) - T24-4 | Always | Below 1 Ω |
| R20-6 (FL-) - T24-2 | ||
| R20-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| R20-6 (FL-) - Body ground |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 1 SPEAKER) |
Disconnect the T25*1 and/or T24*2 front No. 2 speaker connector.
Disconnect the S16*1 and/or S15*2 front No. 1 speaker connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T25-3 - S16-1 | Always | Below 1 Ω |
| T25-1 - S16-2 | ||
| T25-3 - Body ground | Always | 10 kΩ or higher |
| T25-1 - Body ground |
| Tester Connection | Condition | Specified Condition |
| T24-3 - S15-1 | Always | Below 1 Ω |
| T24-1 - S15-2 | ||
| T24-3 - Body ground | Always | 10 kΩ or higher |
| T24-1 - Body ground |
|
| ||||
| OK | |
| 5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
![]() |
Disconnect the S16*1 and/or S15*2 front No. 1 speaker connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 4 Ω |
|
| ||||
| OK | |
| 6.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
Temporarily replace the front No. 2 speaker with a new or normally functioning one (Click here).
Check that the malfunction disappears.
| Result | Proceed to |
| Malfunction disappears | A |
| Malfunction does not disappear | B |
|
| ||||
| A | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - REAR SPEAKER) |
Disconnect the R19 radio and display receiver assembly connector.
Disconnect the S18*1 and/or S17*2 rear speaker connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| R19-1 (RR+) - S18-1 | Always | Below 1 Ω |
| R19-3 (RR-) - S18-2 | ||
| R19-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| R19-3 (RR-) - Body ground |
| Tester Connection | Condition | Specified Condition |
| R19-2 (RL+) - S17-1 | Always | Below 1 Ω |
| R19-6 (RL-) - S17-2 | ||
| R19-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| R19-6 (RL-) - Body ground |
|
| ||||
| OK | |
| 8.INSPECT REAR SPEAKER ASSEMBLY |
![]() |
Disconnect the S18*1 and/or S17*2 rear speaker connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 4 Ω |
|
| ||||
| OK | ||
| ||