Home › SECURITIES › THEFT DETERRENT › BLOCKING SYSTEM

DTC    B1586    Open in Immobiliser Communication Circuit


DESCRIPTION

When the communication line (EFIO - BLK4) between the transponder key ECU assembly and telephone transceiver assembly is stuck on HI output while ignition switch is ON, the telephone transceiver stores DTC B1586.

HINT:
Before troubleshooting for these DTCs, make sure no engine immobiliser system DTCs are present. If present, troubleshoot the engine immobiliser system DTCs first.


DTC Code
DTC Detection Condition
Trouble Area
B1586
The communication line (EFIO - BLK4) between the transponder key ECU assembly and telephone transceiver assembly is stuck on HI while ignition switch is ON.
  1. Telephone transceiver assembly
  2. Transponder key ECU assembly
  3. ECM
  4. Harness or connector

WIRING DIAGRAM


B273047E02


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the telephone transceiver assembly, transponder key ECU assembly or ECM, refer to the Service Bulletin.
  2. When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CLEAR DTC
  1. Clear the DTCs.


NEXT


2.CHECK FOR DTC
  1. Check for DTCs.

    OK:
    DTC B1586 is not output.

    Result 
    Result
    Proceed to
    DTC B1586 is output
    A
    DTC B1586 and other DTCs are output
    B



B
Go to DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


3.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER - ECM)
  1. Disconnect the T31 telephone transceiver assembly connector.

  1. Disconnect the E5*1, E9*2, E13*3 or E25*4 ECM connector.

    1. *1: for 1KD-FTV
    2. *2: for 2TR-FE
    3. *3: for 1GR-FE
    4. *4: for 2TR-FBE

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1KD-FTV:
    Tester Connection
    Condition
    Specified Condition
    T31-8 (BLK3) - E5-30 (IMI)
    Always
    Below 1 Ω
    T31-8 (BLK3) or E5-30 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 2TR-FE:
    Tester Connection
    Condition
    Specified Condition
    T31-8 (BLK3) - E9-16 (IMI)
    Always
    Below 1 Ω
    T31-8 (BLK3) or E9-16 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 1GR-FE:
    Tester Connection
    Condition
    Specified Condition
    T31-8 (BLK3) - E13-16 (IMI)
    Always
    Below 1 Ω
    T31-8 (BLK3) or E13-16 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 2TR-FBE:
    Tester Connection
    Condition
    Specified Condition
    T31-8 (BLK3) - E25-31 (IMI)
    Always
    Below 1 Ω
    T31-8 (BLK3) or E25-31 (IMI) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 1KD-FTV:
    Tester Connection
    Condition
    Specified Condition
    T31-8 (BLK3) or E5-30 (IMI) - Body ground
    Always
    Below 1 V
    for 2TR-FE:
    Tester Connection
    Condition
    Specified Condition
    T31-8 (BLK3) or E9-16 (IMI) - Body ground
    Always
    Below 1 V
    for 1GR-FE:
    Tester Connection
    Condition
    Specified Condition
    T31-8 (BLK3) or E13-16 (IMI) - Body ground
    Always
    Below 1 V
    for 2TR-FBE:
    Tester Connection
    Condition
    Specified Condition
    T31-8 (BLK3) or E25-31 (IMI) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER - TRANSPONDER KEY ECU)
  1. Disconnect the T31 telephone transceiver assembly connector.

  1. Disconnect the T21 transponder key ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T31-2 (BLK4) - T21-13 (EFIO)
    Always
    Below 1 Ω
    T31-2 (BLK4) or T21-13 (EFIO) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    T31-2 (BLK4) or T21-13 (EFIO) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)


    B257265E03
  1. Using an oscilloscope, check the waveform.
    Measurement Condition 
    Item
    Content
    Tester Connection
    T21-13 (EFIO) - T21-16 (GND)
    Tool Setting
    10V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON

    HINT:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

OK:
Waveform is output normally (refer to illustration).

Text in Illustration 
*1
Waveform
*a
Component with harness connected
(Transponder Key ECU Assembly)


NG
Go to step 6
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY 

6.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER - BATTERY AND BODY GROUND)


    B263444E02
  1. Disconnect the T31 telephone transceiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T31-9 (E) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    T31-12 (+B) - T31-9 (E)
    Always
    11 to 14 V
    T31-6 (IG2) - T31-9 (E)
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Telephone Transceiver Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.REPLACE ECM
  1. Temporarily replace the ECM with a new one.


NEXT


8.REGISTER ECU COMMUNICATION ID
  1. Reregister the ECU - ECM communication ID (Refer to the Service Bulletin).


NEXT


9.CLEAR DTC
  1. Clear the DTCs.


NEXT


10.CHECK FOR DTC
  1. Check for DTCs.

    OK:
    DTC B1586 is not output.



NG
Go to step 11
OK

END (ECM IS DEFECTIVE) 

11.REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Temporarily replace the transponder key ECU assembly with a new one (Refer to the Service Bulletin).


NEXT


12.REGISTER ECU COMMUNICATION ID
  1. Reregister the ECU - ECM communication ID (Refer to the Service Bulletin).


NEXT


13.CLEAR DTC
  1. Clear the DTCs.


NEXT


14.CHECK FOR DTC
  1. Check for DTCs.

    OK:
    DTC B1586 is not output.



NG
REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
OK

END (TRANSPONDER KEY ECU IS DEFECTIVE)