DTC B1587 Lost Communication for Immobiliser Communication Circuit |
| DTC Code | DTC Detection Condition | Trouble Area |
| B1587 | Either condition is met:
|
|

| 1.CLEAR DTC |
Clear the DTCs.
| NEXT | |
| 2.CHECK FOR DTC |
Check for DTCs.
|
| ||||
| OK | ||
| ||
| 3.REREGISTER ECU COMMUNICATION ID |
Reregister the ECU - ECM communication ID (Refer to the Service Bulletin).
| NEXT | |
| 4.CLEAR DTC |
Clear the DTCs.
| NEXT | |
| 5.CHECK FOR DTC |
Check for DTCs.
|
| ||||
| OK | ||
| ||
| 6.CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch is off.
Check that the connectors are properly connected to the telephone transceiver assembly, transponder key ECU assembly and ECM.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER - ECM) |
Disconnect the T31 telephone transceiver assembly connector.
Disconnect the E5*1 or E9*2, E13*3 or E25*4 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T31-7 (BLK2) - E5-29 (IMO) | Always | Below 1 Ω |
| T31-7 (BLK2) or E5-29 (IMO) - Body ground | Always | 10 kΩ or higher |
| T31-8 (BLK3) - E5-30 (IMI) | Always | Below 1 Ω |
| T31-8 (BLK3) or E5-30 (IMI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| T31-7 (BLK2) - E9-15 (IMO) | Always | Below 1 Ω |
| T31-7 (BLK2) or E9-15 (IMO) - Body ground | Always | 10 kΩ or higher |
| T31-8 (BLK3) - E9-16 (IMI) | Always | Below 1 Ω |
| T31-8 (BLK3) or E9-16 (IMI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| T31-7 (BLK2) - E13-15 (IMO) | Always | Below 1 Ω |
| T31-7 (BLK2) or E13-15 (IMO) - Body ground | Always | 10 kΩ or higher |
| T31-8 (BLK3) - E13-16 (IMI) | Always | Below 1 Ω |
| T31-8 (BLK3) or E13-16 (IMI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| T31-7 (BLK2) - E25-32 (IMO) | Always | Below 1 Ω |
| T31-7 (BLK2) or E25-32 (IMO) - Body ground | Always | 10 kΩ or higher |
| T31-8 (BLK3) - E25-31 (IMI) | Always | Below 1 Ω |
| T31-8 (BLK3) or E25-31 (IMI) - Body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T31-7 (BLK2) or E5-29 (IMO) - Body ground | Always | Below 1 V |
| T31-8 (BLK3) or E5-30 (IMI) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
| T31-7 (BLK2) or E9-15 (IMO) - Body ground | Always | Below 1 V |
| T31-8 (BLK3) or E9-16 (IMI) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
| T31-7 (BLK2) or E13-15 (IMO) - Body ground | Always | Below 1 V |
| T31-8 (BLK3) or E13-16 (IMI) - Body ground | Always | Below 1 V |
| Tester Connection | Condition | Specified Condition |
| T31-7 (BLK2) or E25-32 (IMO) - Body ground | Always | Below 1 V |
| T31-8 (BLK3) or E25-31 (IMI) - Body ground | Always | Below 1 V |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER - TRANSPONDER KEY ECU) |
Disconnect the T31 telephone transceiver assembly connector.
Disconnect the T21 transponder key ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T31-1 (BLK1) - T21-12 (EFII) | Always | Below 1 Ω |
| T31-1 (BLK1) or T21-12 (EFII) - Body ground | Always | 10 kΩ or higher |
| T31-2 (BLK4) - T21-13 (EFIO) | Always | Below 1 Ω |
| T31-2 (BLK4) or T21-13 (EFIO) - Body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T31-1 (BLK1) or T21-12 (EFII) - Body ground | Always | Below 1 V |
| T31-2 (BLK4) or T21-13 (EFIO) - Body ground | Always | Below 1 V |
|
| ||||
| OK | |
| 9.REPLACE TRANSPONDER KEY ECU ASSEMBLY |
Temporarily replace the transponder key ECU assembly with a new one (Refer to the Service Bulletin).
| NEXT | |
| 10.REGISTER ECU COMMUNICATION ID |
Register the ECU - ECM communication ID (Refer to the Service Bulletin).
| NEXT | |
| 11.CLEAR DTC |
Clear the DTCs.
| NEXT | |
| 12.CHECK FOR DTC |
Check for DTCs.
|
| ||||
| OK | ||
| ||
| 13.REPLACE ECM |
Temporarily replace the ECM with a new one.
| NEXT | |
| 14.REGISTER ECU COMMUNICATION ID |
Register the ECU - ECM communication ID (Refer to the Service Bulletin).
| NEXT | |
| 15.CLEAR DTC |
Clear the DTCs.
| NEXT | |
| 16.CHECK FOR DTC |
Check for DTCs.
|
| ||||
| OK | ||
| ||