Home › SECURITIES › THEFT DETERRENT › BLOCKING SYSTEM

DTC    B1587    Lost Communication for Immobiliser Communication Circuit


DESCRIPTION

When one of the following occurs: 1) the telephone transceiver assembly detects errors in its own communications with the transponder key ECU assembly; 2) the telephone transceiver assembly detects errors in the communication lines; 3) the ECU communication ID between the transponder key ECU assembly and telephone transceiver assembly is different and an engine start is attempt, the telephone transceiver assembly stores DTC B1587.

HINT:
Before troubleshooting for these DTCs, make sure no engine immobiliser system DTCs are present. If present, troubleshoot the engine immobiliser system DTCs first.


DTC Code
DTC Detection Condition
Trouble Area
B1587
Either condition is met:
  1. Error in communication between telephone transceiver assembly and transponder key ECU assembly
  2. Error in communication lines
  3. Communication ID is different during communication with transponder key ECU assembly
  1. Telephone transceiver assembly
  2. Transponder key ECU assembly
  3. ECM
  4. Harness or connector

WIRING DIAGRAM


B315875E01


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the telephone transceiver assembly, transponder key ECU assembly or ECM, refer to the Service Bulletin.
  2. When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CLEAR DTC
  1. Clear the DTCs.


NEXT


2.CHECK FOR DTC
  1. Check for DTCs.

    OK:
    DTC B1587 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK 

3.REREGISTER ECU COMMUNICATION ID
  1. Reregister the ECU - ECM communication ID (Refer to the Service Bulletin).


NEXT


4.CLEAR DTC
  1. Clear the DTCs.


NEXT


5.CHECK FOR DTC
  1. Check for DTCs.

    OK:
    DTC B1587 is not output.



NG
Go to step 6
OK

END 

6.CHECK CONNECTION OF CONNECTOR
  1. Turn the ignition switch is off.

  1. Check that the connectors are properly connected to the telephone transceiver assembly, transponder key ECU assembly and ECM.

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTOR CORRECTLY
OK


7.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER - ECM)
  1. Disconnect the T31 telephone transceiver assembly connector.

  1. Disconnect the E5*1, E9*2, E13*3, E25*4 or E31*5 ECM connector.

    1. *1: for 1KD-FTV (except i-ART)
    2. *2: for 2TR-FE
    3. *3: for 1GR-FE
    4. *4: for 2TR-FBE
    5. *5: for 1KD-FTV (for i-ART)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1KD-FTV (except i-ART):
    Tester Connection
    Condition
    Specified Condition
    T31-7 (BLK2) - E5-29 (IMO)
    Always
    Below 1 Ω
    T31-7 (BLK2) or E5-29 (IMO) - Body ground
    Always
    10 kΩ or higher
    T31-8 (BLK3) - E5-30 (IMI)
    Always
    Below 1 Ω
    T31-8 (BLK3) or E5-30 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 2TR-FE:
    Tester Connection
    Condition
    Specified Condition
    T31-7 (BLK2) - E9-15 (IMO)
    Always
    Below 1 Ω
    T31-7 (BLK2) or E9-15 (IMO) - Body ground
    Always
    10 kΩ or higher
    T31-8 (BLK3) - E9-16 (IMI)
    Always
    Below 1 Ω
    T31-8 (BLK3) or E9-16 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 1GR-FE:
    Tester Connection
    Condition
    Specified Condition
    T31-7 (BLK2) - E13-15 (IMO)
    Always
    Below 1 Ω
    T31-7 (BLK2) or E13-15 (IMO) - Body ground
    Always
    10 kΩ or higher
    T31-8 (BLK3) - E13-16 (IMI)
    Always
    Below 1 Ω
    T31-8 (BLK3) or E13-16 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 2TR-FBE:
    Tester Connection
    Condition
    Specified Condition
    T31-7 (BLK2) - E25-32 (IMO)
    Always
    Below 1 Ω
    T31-7 (BLK2) or E25-32 (IMO) - Body ground
    Always
    10 kΩ or higher
    T31-8 (BLK3) - E25-31 (IMI)
    Always
    Below 1 Ω
    T31-8 (BLK3) or E25-31 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV (for i-ART):
    Tester Connection
    Condition
    Specified Condition
    T31-7 (BLK2) - E31-29 (IMO)
    Always
    Below 1 Ω
    T31-7 (BLK2) or E31-29 (IMO) - Body ground
    Always
    10 kΩ or higher
    T31-8 (BLK3) - E31-28 (IMI)
    Always
    Below 1 Ω
    T31-8 (BLK3) or E31-28 (IMI) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 1KD-FTV (except i-ART):
    Tester Connection
    Condition
    Specified Condition
    T31-7 (BLK2) or E5-29 (IMO) - Body ground
    Always
    Below 1 V
    T31-8 (BLK3) or E5-30 (IMI) - Body ground
    Always
    Below 1 V
    for 2TR-FE:
    Tester Connection
    Condition
    Specified Condition
    T31-7 (BLK2) or E9-15 (IMO) - Body ground
    Always
    Below 1 V
    T31-8 (BLK3) or E9-16 (IMI) - Body ground
    Always
    Below 1 V
    for 1GR-FE:
    Tester Connection
    Condition
    Specified Condition
    T31-7 (BLK2) or E13-15 (IMO) - Body ground
    Always
    Below 1 V
    T31-8 (BLK3) or E13-16 (IMI) - Body ground
    Always
    Below 1 V
    for 2TR-FBE:
    Tester Connection
    Condition
    Specified Condition
    T31-7 (BLK2) or E25-32 (IMO) - Body ground
    Always
    Below 1 V
    T31-8 (BLK3) or E25-31 (IMI) - Body ground
    Always
    Below 1 V
    for 1KD-FTV (for i-ART):
    Tester Connection
    Condition
    Specified Condition
    T31-7 (BLK2) or E31-29 (IMO) - Body ground
    Always
    Below 1 V
    T31-8 (BLK3) or E31-28 (IMI) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER - TRANSPONDER KEY ECU)
  1. Disconnect the T31 telephone transceiver assembly connector.

  1. Disconnect the T21 transponder key ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T31-1 (BLK1) - T21-12 (EFII)
    Always
    Below 1 Ω
    T31-1 (BLK1) or T21-12 (EFII) - Body ground
    Always
    10 kΩ or higher
    T31-2 (BLK4) - T21-13 (EFIO)
    Always
    Below 1 Ω
    T31-2 (BLK4) or T21-13 (EFIO) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    T31-1 (BLK1) or T21-12 (EFII) - Body ground
    Always
    Below 1 V
    T31-2 (BLK4) or T21-13 (EFIO) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Temporarily replace the transponder key ECU assembly with a new one (Refer to the Service Bulletin).


NEXT


10.REGISTER ECU COMMUNICATION ID
  1. Register the ECU - ECM communication ID (Refer to the Service Bulletin).


NEXT


11.CLEAR DTC
  1. Clear the DTCs.


NEXT


12.CHECK FOR DTC
  1. Check for DTCs.

    OK:
    DTC B1587 is not output.



NG
Go to step 13
OK

END (TRANSPONDER KEY ECU IS DEFECTIVE) 

13.REPLACE ECM
  1. Temporarily replace the ECM with a new one.


NEXT


14.REGISTER ECU COMMUNICATION ID
  1. Register the ECU - ECM communication ID (Refer to the Service Bulletin).


NEXT


15.CLEAR DTC
  1. Clear the DTCs.


NEXT


16.CHECK FOR DTC
  1. Check for DTCs.

    OK:
    DTC B1587 is not output.



NG
REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
OK

END (ECM IS DEFECTIVE)