EGR COOLER (w/ Glow Plug Controller) > INSTALLATION |
| 1. INSTALL EGR COOLER INSULATOR |
![]() |
Install the 2 EGR cooler insulators to the EGR cooler.
| *1 | No. 2 EGR Cooler Insulator |
| *2 | No. 1 EGR Cooler Insulator |
| 2. INSTALL NO. 2 EGR VALVE ASSEMBLY |
![]() |
Using a 6 mm hexagon wrench, install 2 new gaskets, the EGR valve adapter, No. 2 EGR valve, EGR cooler and 3 plate washers with the 3 hexagon socket head cap bolts.
Install the bolt labeled A.
| 3. TEMPORARILY INSTALL INTAKE AIR CONNECTOR WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY |
Install 2 new gaskets and the electric EGR control valve to the stud bolts of the intake air connector.
Temporarily install the intake air connector with electric EGR control valve to the EGR valve adapter with the 3 nuts.

| *1 | Intake Air Connector | *2 | New Gasket |
| *3 | Electric EGR Control Valve | *4 | EGR Valve Adapter |
| 4. TEMPORARILY INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER |
Install a new gasket to the intake manifold.
Install a new gasket to the stud bolts of the cylinder head.
Set the electric EGR control valve with No. 2 EGR valve and EGR cooler on the intake manifold and cylinder head.
Temporarily install the intake air connector to the intake manifold with the 3 bolts labeled A in the illustration.
Temporarily install the EGR cooler to the intake manifold with the 2 bolts labeled B in the illustration.
Temporarily install the EGR cooler to the cylinder head with the 2 nuts labeled C in the illustration.

| *1 | New Gasket | *2 | Intake Manifold |
| *3 | Intake Air Connector | *4 | EGR Cooler |
| 5. TIGHTEN ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER |
Tighten the 3 bolts labeled A in the illustration.
Tighten the 2 bolts labeled B in the illustration.
Tighten the 2 nuts labeled C in the illustration.
Temporarily install the EGR valve bracket with the 3 bolts.
Tighten the bolt labeled D in the illustration.
Tighten the 2 bolts labeled E in the illustration.
Tighten the 3 nuts labeled F in the illustration.

| *1 | EGR Valve Bracket | - | - |
| 6. CONNECT NO. 3 WATER BY-PASS PIPE |
Connect the No. 3 water by-pass pipe with the 2 bolts.
| 7. CONNECT ENGINE WIRE |
Connect the engine wire with the bolt.
Attach the 2 wire harness clamps.
| 8. INSTALL THROTTLE BODY BRACKET |
Install the throttle body bracket with the 3 bolts.
| 9. INSTALL WIRING HARNESS CLAMP BRACKET |
Install the wiring harness clamp bracket with the bolt.
| 10. INSTALL GAS FILTER BRACKET WITH GAS FILTER |
Install the gas filter bracket with gas filter with the bolt.
Connect the vacuum hose.
| 11. INSTALL MANIFOLD ABSOLUTE PRESSURE SENSOR |
Install the manifold absolute pressure sensor with the bolt.
Connect the vacuum hose and manifold absolute pressure sensor connector.
| 12. INSTALL NO. 5 WATER BY-PASS PIPE |
![]() |
Install the No. 5 water by-pass pipe with the 2 bolts.
| *a | Upper Side |
Connect the 2 water hoses to the electric EGR control valve.
Attach the 2 wire harness clamps.
| 13. INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY |
Temporarily install the No. 1, No. 2 and No. 3 injection pipes with the union nuts.
Install the 2 No. 3 injection pipe clamps with the 4 nuts.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the common rail side.
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.
| 14. INSTALL FUEL INLET PIPE SUB-ASSEMBLY |
Temporarily install the fuel inlet pipe with the union nuts.
![]() |
Install the No. 2 injection pipe clamp with the bolt.
| *1 | Fuel Inlet Pipe |
| *2 | Paint Mark |
| *3 | No. 2 Fuel Pipe |
Using a 17 mm union nut wrench, tighten the fuel inlet pipe union nut on the common rail side.
Using a 17 mm union nut wrench, tighten the fuel inlet pipe union nut on the fuel supply pump side.
| 15. INSTALL FUEL PIPE INSULATOR |
Install the fuel pipe insulator to the fuel pipes.
| 16. INSTALL MANIFOLD STAY WITH VACUUM SWITCHING VALVE |
Install the manifold stay with vacuum switching valve with the 2 bolts.
![]() |
Connect the connector and 2 No. 2 vacuum transmitting hoses and attach the 2 clamps as shown in the illustration.
| *1 | No. 2 Vacuum Transmitting Hose |
| *2 | White Paint Mark |
| 17. CONNECT WATER BY-PASS HOSE |
Connect the 6 water by-pass hoses.

| *1 | Paint Mark | - | - |
| *a | Upper Side | *b | LH Side |
| 18. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE |
Install a new O-ring to the engine oil level dipstick guide.
Apply a small amount of clean engine oil to the O-ring.
Install the engine oil level dipstick guide with the bolt.
Attach the wire harness clamp.
Install the engine oil level dipstick and gasket.
| 19. INSTALL FRONT FENDER SEAL |
Install the front fender seal with the 5 clips.
| 20. INSTALL FRONT FENDER APRON SEAL UPPER |
Install the front fender apron seal upper with the 5 clips.
| 21. INSTALL FRONT WHEEL LH |
| 22. INSTALL DIESEL THROTTLE BODY ASSEMBLY |
| 23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 24. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
![]() |
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's B line.
| Item | Specified Condition |
| A/T | 11.1 liters (11.7 US qts, 9.8 Imp. qts) |
| M/T | 9.8 liters (10.4 US qts, 8.6 Imp. qts) |
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
![]() |
Using a wrench, install the vent plug.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2,500 to 3,000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
After the coolant cools down, check that the coolant level is at the F line.
If the coolant level is below the F line, add TOYOTA SLLC to the F line.
| 25. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Check if the engine starts.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.*1
![]() |
Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak.*2
| *a | Reference (Active Test Operation) |
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine / DTC.
Read Current DTCs.
Clear the DTCs (Click here).
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine / DTC.
Read Current DTCs.
| 26. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17.1 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks.
If no external leaks are found, check the cylinder block and head.
| 27. INSPECT FOR FUEL LEAK |
Perform the Active Test.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine / Active Test.
Perform the Active Test.
| Intelligent Tester Display | Test Part | Control Range | Diagnostic Note |
| Test the Fuel Leak | Pressurize common rail interior and check for fuel leaks | Stop/Start |
|
| 28. INSTALL NO. 1 ENGINE UNDER COVER |