EGR COOLER (w/ Glow Plug Controller) > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE DIESEL THROTTLE BODY ASSEMBLY |
| 4. REMOVE NO. 1 ENGINE UNDER COVER |
| 5. DRAIN ENGINE COOLANT |
![]() |
Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.
Loosen the cylinder block drain cock plug and the radiator drain cock plug.

| 6. REMOVE FRONT WHEEL LH |
| 7. REMOVE FRONT FENDER APRON SEAL UPPER |
Remove the 5 clips and front fender apron seal upper.
| 8. REMOVE FRONT FENDER SEAL |
Remove the 5 clips and front fender seal.
| 9. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE |
Remove the engine oil level dipstick and gasket.
![]() |
Detach the wire harness clamp.
Remove the bolt and engine oil level dipstick guide.
Remove the O-ring from the engine oil level dipstick guide.
| 10. DISCONNECT WATER BY-PASS HOSE |
Disconnect the 6 water by-pass hoses.

| 11. REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE |
![]() |
Disconnect the connector and 2 No. 2 vacuum transmitting hoses and detach the 2 clamps.
![]() |
Remove the 2 bolts and manifold stay with vacuum switching valve.
| 12. REMOVE FUEL PIPE INSULATOR |
Remove the fuel pipe insulator from the fuel pipes.
| 13. REMOVE FUEL INLET PIPE SUB-ASSEMBLY |
![]() |
Remove the bolt and No. 2 injection pipe clamp.
Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
| 14. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY |
![]() |
Disconnect the 4 injector connectors and electric EGR control valve connector.
Detach the 2 wire harness clamps.
![]() |
Remove the 4 nuts and 2 No. 3 injection pipe clamps.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
| *a | Injector Side |
| *b | Common Rail Side |
| 15. REMOVE NO. 5 WATER BY-PASS PIPE |
![]() |
Detach the 2 wire harness clamps.
![]() |
Disconnect the 2 water hoses from the electric EGR control valve.
Remove the 2 bolts and No. 5 water by-pass pipe.
| 16. REMOVE MANIFOLD ABSOLUTE PRESSURE SENSOR |
![]() |
Disconnect the manifold absolute pressure sensor connector and vacuum hose.
Remove the bolt and manifold absolute pressure sensor.
| 17. REMOVE GAS FILTER BRACKET WITH GAS FILTER |
![]() |
Disconnect the vacuum hose.
Remove the bolt and gas filter bracket with gas filter.
| 18. REMOVE WIRING HARNESS CLAMP BRACKET |
![]() |
Remove the bolt and wiring harness clamp bracket.
| 19. REMOVE THROTTLE BODY BRACKET |
![]() |
Remove the 3 bolts and throttle body bracket.
| 20. DISCONNECT ENGINE WIRE |
![]() |
Detach the 2 wire harness clamps.
Remove the bolt and disconnect the engine wire.
| 21. DISCONNECT NO. 3 WATER BY-PASS PIPE |
![]() |
Remove the 2 bolts and disconnect the No. 3 water by-pass pipe.
| 22. REMOVE EGR VALVE BRACKET |
![]() |
Remove the 3 bolts and EGR valve bracket.
| 23. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER |
Remove the 5 bolts, 2 nuts and electric EGR control valve with No. 2 EGR valve and EGR cooler.

| *1 | Gasket | - | - |
Remove the 2 gaskets from the cylinder head and intake manifold.
| 24. REMOVE INTAKE AIR CONNECTOR WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY |
![]() |
Remove the 3 nuts, intake air connector with electric EGR control valve and gasket.
| 25. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY |
Remove the electric EGR control valve and gasket from the intake air connector.
| 26. REMOVE EGR VALVE ADAPTER |
![]() |
Using a 6 mm hexagon wrench, remove the 3 hexagon socket head cap bolts, 3 plate washers, EGR valve adapter and gasket.
| 27. REMOVE NO. 2 EGR VALVE ASSEMBLY |
![]() |
Remove the bolt, No. 2 EGR valve and gasket.
| 28. REMOVE EGR COOLER INSULATOR |
![]() |
Remove the 2 EGR cooler insulators from the EGR cooler.
| *1 | No. 2 EGR Cooler Insulator |
| *2 | No. 1 EGR Cooler Insulator |