Home › ENGINE ยท 1KD-FTV › EMISSION CONTROL › EGR COOLER (w/ Glow Plug Controller)

EGR COOLER (w/ Glow Plug Controller) > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE DIESEL THROTTLE BODY ASSEMBLY
(Click here)


4. REMOVE NO. 1 ENGINE UNDER COVER


5. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A099591E01
  1. Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.



  1. Loosen the cylinder block drain cock plug and the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



    A112147E01



6. REMOVE FRONT WHEEL LH


7. REMOVE FRONT FENDER APRON SEAL UPPER
  1. Remove the 5 clips and front fender apron seal upper.



8. REMOVE FRONT FENDER SEAL
  1. Remove the 5 clips and front fender seal.



9. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the engine oil level dipstick and gasket.



    A271900
  1. Detach the wire harness clamp.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.



10. DISCONNECT WATER BY-PASS HOSE


  1. Disconnect the 6 water by-pass hoses.


    A271899



11. REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE


    A271765
  1. Disconnect the connector and 2 No. 2 vacuum transmitting hoses and detach the 2 clamps.



    A271766
  1. Remove the 2 bolts and manifold stay with vacuum switching valve.



12. REMOVE FUEL PIPE INSULATOR
  1. Remove the fuel pipe insulator from the fuel pipes.



13. REMOVE FUEL INLET PIPE SUB-ASSEMBLY


    A252241
  1. Remove the bolt and No. 2 injection pipe clamp.

  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.



14. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. After removing the injection pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the injection pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.



    A271763
  1. Disconnect the 4 injector connectors and electric EGR control valve connector.

  1. Detach the 2 wire harness clamps.



    A271903
  1. Remove the 4 nuts and 2 No. 3 injection pipe clamps.



    A271904E01
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
    Text in Illustration 
    *a
    Injector Side
    *b
    Common Rail Side



15. REMOVE NO. 5 WATER BY-PASS PIPE


    A252245
  1. Detach the 2 wire harness clamps.



    A271905
  1. Disconnect the 2 water hoses from the electric EGR control valve.

  1. Remove the 2 bolts and No. 5 water by-pass pipe.



16. REMOVE MANIFOLD ABSOLUTE PRESSURE SENSOR


    A252248
  1. Disconnect the manifold absolute pressure sensor connector and vacuum hose.

  1. Remove the bolt and manifold absolute pressure sensor.



17. REMOVE GAS FILTER BRACKET WITH GAS FILTER


    A252249
  1. Disconnect the vacuum hose.

  1. Remove the bolt and gas filter bracket with gas filter.



18. REMOVE WIRING HARNESS CLAMP BRACKET


    A271906
  1. Remove the bolt and wiring harness clamp bracket.



19. REMOVE THROTTLE BODY BRACKET


    A252251
  1. Remove the 3 bolts and throttle body bracket.



20. DISCONNECT ENGINE WIRE


    A252252
  1. Detach the 2 wire harness clamps.

  1. Remove the bolt and disconnect the engine wire.



21. DISCONNECT NO. 3 WATER BY-PASS PIPE


    A271907
  1. Remove the 2 bolts and disconnect the No. 3 water by-pass pipe.



22. REMOVE EGR VALVE BRACKET


    A271908
  1. Remove the 3 bolts and EGR valve bracket.



23. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER


  1. Remove the 5 bolts, 2 nuts and electric EGR control valve with No. 2 EGR valve and EGR cooler.


    A271897E01


    Text in Illustration 
    *1
    Gasket
    -
    -

  1. Remove the 2 gaskets from the cylinder head and intake manifold.



24. REMOVE INTAKE AIR CONNECTOR WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY


    A252257
  1. Remove the 3 nuts, intake air connector with electric EGR control valve and gasket.



25. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY
  1. Remove the electric EGR control valve and gasket from the intake air connector.



26. REMOVE EGR VALVE ADAPTER


    A252258
  1. Using a 6 mm hexagon wrench, remove the 3 hexagon socket head cap bolts, 3 plate washers, EGR valve adapter and gasket.



27. REMOVE NO. 2 EGR VALVE ASSEMBLY


    A252259
  1. Remove the bolt, No. 2 EGR valve and gasket.



28. REMOVE EGR COOLER INSULATOR


    A252260E01
  1. Remove the 2 EGR cooler insulators from the EGR cooler.
    Text in Illustration 
    *1
    No. 2 EGR Cooler Insulator
    *2
    No. 1 EGR Cooler Insulator