BACK DOOR > REASSEMBLY |
| 1. INSTALL BACK DOOR STAY ASSEMBLY LH |
When using a new bolt:
Clean the threaded portion on the vehicle body with a non-residue solvent.
When reusing a bolt:
Clean the threaded portion on the vehicle body and bolt with a non-residue solvent.
Apply adhesive to the threads of the bolt.
Install the back door stay with the 4 bolts.
| 2. INSTALL BACK DOOR STAY ASSEMBLY RH |
| 3. INSTALL BACK DOOR LOWER STOPPER |
Install the back door lower stopper with the bolt.
| 4. INSTALL BACK DOOR PANEL CUSHION |
![]() |
Install 2 new back door panel cushions.
| *1 | for Upper Side |
| *2 | for Lower Side |
| 5. INSTALL BACK DOOR GLASS CHANNEL LH |
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove the double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Install a new back door glass channel.
Using a heat light, heat the vehicle body.
Remove the peeling paper from the face of a new back door glass channel.
Install the back door glass channel.
Install the 2 clips.
| 6. INSTALL BACK DOOR GLASS CHANNEL RH |
| 7. INSTALL REAR WASHER NOZZLE SUB-ASSEMBLY |
Attach the 2 claws to install the rear washer nozzle.
Connect the hose.
| 8. INSTALL REAR SPOILER |
Attach the 4 clips to install the rear spoiler.
Install the 3 nuts.
Install the 2 grommets.
| 9. INSTALL NO. 2 BACK DOOR SERVICE HOLE COVER |
Connect the connector and attach the clamp.
Attach the 4 claws to install the No. 2 back door service hole cover.
| 10. INSTALL REAR WIPER MOTOR GROMMET |
![]() |
Apply MP grease to the entire inner surface of the wiper motor grommet.
| *1 | MP grease |
![]() |
Install the rear wiper motor grommet with the position mark facing upward as shown in the illustration.
| *1 | Position Mark |
| 11. INSTALL REAR WIPER MOTOR ASSEMBLY |
![]() |
Install the wiper motor with the 3 bolts.
Connect the connector.
| 12. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY |
Operate the rear wiper, and stop the rear wiper motor at the automatic stop position.
![]() |
Clean the wiper pivot serrations with a wire brush.
| *1 | Wiper Arm Pivot Serrations |
| *2 | Wire Brush |
| *3 | Wiper Pivot Serrations |
![]() |
Install the arm and blade with the nut. Make sure that the arm and blade comes to the position shown in the illustration.
| *1 | Ceramic Line |
Operate the rear wiper while spraying water or washer fluid on the glass. Make sure that there is no interference between the blade and pillar.
![]() |
Close the wiper arm head cap.
| 13. INSTALL REAR LIGHT ASSEMBLY LH |
Attach the rear light assembly LH with the claw and pin.
Install the 2 nuts to install the rear light assembly LH.
Connect the connector.
| 14. INSTALL REAR LIGHT ASSEMBLY RH |
| 15. INSTALL BACK DOOR OUTSIDE GARNISH |
Attach the 2 clips to install the back door outside garnish.
w/ Rear View Monitor System:
Install the nut.
w/o Rear View Monitor System:
Install the 3 nuts.
| 16. INSTALL REAR TELEVISION CAMERA ASSEMBLY (w/ Rear View Monitor System) |
Install the rear television camera assembly with the 2 nuts.
Connect the connector.
| 17. INSTALL BACK DOOR OUTSIDE HANDLE |
Install the back door outside handle with the 2 nuts.
| 18. INSTALL BACK DOOR LOCK ASSEMBLY |
![]() |
Temporarily install the back door lock assembly with the 3 bolts.
Tighten the bolts in the order shown in the illustration.
Attach the back door lock cable assembly.
Connect the clamp and connect the connector.

| *1 | Back Door Lock Cable Assembly | - | - |
| 19. INSTALL BACK DOOR TRIM BOARD ASSEMBLY |
Attach the 16 clips to install the back door trim board.
| 20. INSTALL DOOR PULL HANDLE |
Attach the 4 clips to install the door pull handle.