Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

DTC    B15C0    Short in GPS Antenna

DTC    B15C1    Open in GPS Antenna


DESCRIPTION

This DTC is stored when a malfunction occurs in the navigation antenna assembly.

DTC Code
DTC Detection Condition
Trouble Area
B15C0
A GPS antenna error.
  1. Navigation antenna assembly (w/o Blocking System)
  2. Navigation antenna cord sub-assembly (w/o Blocking System)
  3. Instrument panel integration antenna assembly (w/ Blocking System)
  4. Divider antenna assembly (w/ Blocking System)
  5. Navigation receiver assembly
B15C1
An error of the power source to the GPS antenna.
  1. Navigation antenna assembly (w/o Blocking System)
  2. Navigation antenna cord sub-assembly (w/o Blocking System)
  3. Instrument panel integration antenna assembly (w/ Blocking System)
  4. Divider antenna assembly (w/ Blocking System)
  5. Navigation receiver assembly

WIRING DIAGRAM


w/o Blocking System

E238677E01


w/ Blocking System

E238679E01


INSPECTION PROCEDURE

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)  

3.CHECK HARNESS AND CONNECTOR
  1. *1: w/o Blocking System
  2. *2: w/ Blocking System
  1. Check if the navigation antenna assembly*1 or instrument panel integration antenna assembly*2 is securely connected to the navigation receiver assembly.

    OK:
    Navigation antenna assembly*1 or instrument panel integration antenna assembly*2 is securely connected.

    Result 
    Result
    Proceed to
    OK (w/o Blocking System)
    A
    OK (w/ Blocking System)
    B
    NG
    C



B
Go to step 6

C
SECURELY CONNECT NAVIGATION ANTENNA ASSEMBLY
A


4.CHECK NAVIGATION ANTENNA CORD SUB-ASSEMBLY


    E246993E01
  1. Disconnect the A navigation antenna assembly connector.

  1. Disconnect the G navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A (Core wire) - B (Core wire)
    Always
    Below 1 Ω
    A (Shield) - B (Shield)
    Always
    Below 1 Ω
    A (Core wire) - A (Shield) or B (Core wire) - B (Shield)
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Navigation antenna cord sub-assembly)
    *1
    Core wire
    *2
    Shield



NG
REPLACE NAVIGATION ANTENNA CORD SUB-ASSEMBLY (Click here)
OK


5.REPLACE NAVIGATION ANTENNA ASSEMBLY
  1. Temporarily replace the navigation antenna assembly with a new or normally functioning one (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

END (NAVIGATION ANTENNA ASSEMBLY IS DEFECTIVE) 

6.REPLACE INSTRUMENT PANEL INTEGRATION ANTENNA ASSEMBLY
  1. Temporarily replace the instrument panel integration antenna assembly with a new or normally functioning one.

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
Go to step 7
OK

END (INSTRUMENT PANEL INTEGRATION ANTENNA ASSEMBLY IS DEFECTIVE) 

7.REPLACE DIVIDER ANTENNA ASSEMBLY
  1. Temporarily replace the divider antenna assembly with a new or normally functioning one.

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

END (DIVIDER ANTENNA ASSEMBLY IS DEFECTIVE)