Home › BRAKE › BRAKE › FRONT BRAKE (for TMMIN Made)

FRONT BRAKE (for TMMIN Made) > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.



1. INSTALL FRONT DISC


    C111383E01
  1. Align the matchmarks and install the disc.

    HINT:
    When replacing the disc with a new one, select the installation position where the disc has the smallest runout.



2. INSTALL DISC BRAKE CYLINDER ASSEMBLY LH
  1. Install the cylinder with the 2 bolts.

    Torque:
    122 N*m{ 1244 kgf*cm , 90 ft.*lbf }



3. CONNECT FRONT NO. 1 WHEEL CYLINDER TUBE LH
  1. Using a union nut wrench, connect the tube to the cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



4. INSTALL FRONT ANTI-SQUEAL SHIM KIT


    C238121E02
  1. Apply disc brake grease to both sides of each No. 1 shim.

  1. Install the No. 1 and No. 2 shims to each pad.

    NOTICE:
    1. When replacing worn pads, the shims must be replaced together with the pads.
    2. Install the shims in the correct position and direction.



5. INSTALL FRONT DISC BRAKE PAD
  1. Install the 2 disc brake pads to the cylinder.

    NOTICE:
    There should be no oil or grease on the friction surface of the pads and disc.



6. INSTALL FRONT DISC BRAKE ANTI-RATTLE SPRING


    F043185E05
  1. Install the 2 pins and anti-rattle spring.

    HINT:
    Install the spring together with the pin on the bottom side.

  1. Install the 2 clips.

    NOTICE:
    When installing the clip, be sure to install the clip with the handle facing the center of the vehicle.



7. FILL RESERVOIR WITH BRAKE FLUID

Fluid :
SAE J1703 or FMVSS No. 116 DOT 3



8. BLEED AIR FROM BRAKE MASTER CYLINDER

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed air from the master cylinder.

  1. Using a union nut wrench, disconnect the 2 brake lines from the master cylinder.



    C247712
  1. Slowly depress and hold the brake pedal.



    C247713
  1. Cover the outer holes with your finger, and release the pedal.

  1. Repeat the 2 previous steps 3 or 4 times.

  1. Using a union nut wrench, connect the 2 brake lines to the master cylinder.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



9. BLEED AIR FROM BRAKE LINE
  1. Remove the bleeder plug cap.

  1. Connect the vinyl tube to the bleeder plugs.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.

  1. Repeat the 2 previous steps until all the air in the brake fluid is gone.

  1. Tighten the bleeder plug.

    Torque:
    for front brake:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }
    for rear brake:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the cap.

  1. Bleed air from the brake line for each wheel by repeating the above procedures.



10. BLEED AIR FROM CLUTCH LINE (for Manual Transmission)
  1. Remove the brake master cylinder reservoir filler cap assembly.

  1. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the clutch line.

    Fluid:
    Made
    Fluid
    except TSAM Made
    SAE J1703 or FMVSS No. 116 DOT 3
    for TSAM Made
    SAE J1704 or FMVSS No. 116 DOT 4

  1. Remove the bleeder plug cap.



    C112661E08
  1. Connect a vinyl tube to the bleeder plug.

  1. Depress the clutch pedal several times, and then loosen the bleeder plug with the pedal depressed.

  1. At the point when fluid stops coming out, tighten the bleeder plug, and then release the clutch pedal.

  1. Repeat the previous 2 steps until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

  1. Install the bleeder plug cap.

  1. Check that all the air has been bled out of the clutch line.

  1. Check for brake fluid leaks.

  1. Check the brake fluid level in the reservoir.

    1. w/o VSC:

    2. w/ VSC:

  1. Install the brake master cylinder reservoir filler cap assembly.



11. CHECK BRAKE FLUID LEVEL IN RESERVOIR


    F052092
  1. Check the fluid level.
    If the brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3



12. CHECK FOR BRAKE FLUID LEAKAGE


13. INSTALL FRONT WHEEL

Torque:
105 N*m{ 1071 kgf*cm , 77 ft.*lbf }