DIFFERENTIAL CARRIER OIL SEAL > REPLACEMENT > Preparation
|  |
|
SST

| 09308-00010
| Oil Seal Puller
| 
| 09308-10010
| Oil Seal Puller
| 
| 09316-60011
| Transmission & Transfer Bearing Replacer
| 
| (09316-00011)
| Replacer Pipe
| 
| (09316-00021)
| Replacer A
| 
| 09330-00021
| Companion Flange Holding Tool
| 
| (09330-00030)
| Pin
| 
| 09554-30011
| Differential Oil Seal Replacer
| 
| 09556-22010
| Drive Pinion Front Bearing Remover
| 
| 09930-00010
| Drive Shaft Nut Chisel
| 
| (09931-00010)
| Handle
| 
| (09931-00020)
| Nut Chisel
| 
| 09950-30012
| Puller A Set
| 
| (09951-03010)
| Upper Plate
| 
| (09953-03010)
| Center Bolt
| 
| (09954-03010)
| Arm
| 
| (09955-03030)
| Lower Plate 130
| 
| (09956-03040)
| Adapter 22
| 
| 09961-00950
| Torque Wrench Adaptor
| |
|
EQUIPMENTBrass bar
| -
| Chisel
| -
| Dial indicator with magnetic base
| -
| Feeler gauge
| -
| Hammer
| -
| Micrometer
| -
| MP grease
| -
| Needle nose pliers
| -
| Plastic hammer
| -
| Press
| -
| Red lead
| -
| Screwdriver
| -
| Tape
| -
| Torque wrench
| -
| Vernier calipers
| -
| |
|
LUBRICANT
(2012/01 - 2012/10)
/ Recommended ViscosityItem
| Temperature
| Viscosity
| Front Differential Rear Differential
| Above -18°C (0°F)
| SAE 90
| Below -18°C (0°F)
| SAE 80W-90 or SAE 80W
|
LUBRICANT
(2012/01 - 2012/10)
/ Differential Oil TypeItem
| Oil type
| Front Differential Rear Differential
| Hypoid gear oil API GL-5
|
LUBRICANT
(2012/01 - 2012/10)
/ Standard Differential Oil CapacityItem
| Specified Condition
| Front Differential
| 1.40 to 1.50 liters (1.48 to 1.58 US qts., 1.23 to 1.32 Imp. qts.)
| Rear Differential
| 3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.)
| w/ Differential Lock
| 2.85 to 2.95 liters (3.01 to 3.12 US qts., 2.51 to 2.59 Imp. qts.)
| 4WD, Pre-Runner and made DANA
| 2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.)
| |
|
LUBRICANT
(2012/10 - ) / Recommended ViscosityItem
| Temperature
| Viscosity
| Front Differential Rear Differential
| Above -18°C (0°F)
| SAE 90
| Below -18°C (0°F)
| SAE 80W-90 or SAE 80W
|
LUBRICANT
(2012/10 - ) / Differential Oil TypeItem
| Oil type
| Front Differential Rear Differential
| Hypoid gear oil API GL-5
|
LUBRICANT
(2012/10 - ) / Standard Differential Oil CapacityItem
| Specified Condition
| Front Differential
| 1.40 to 1.50 liters (1.48 to 1.58 US qts., 1.23 to 1.32 Imp. qts.)
| Rear Differential
| 3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.)
| 4WD, Pre-Runner and made DANA
| 2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.)
| |
|
RECOMMENDED TOOLS
| 09011-2C590
| Socket Wrench 30mm/12p
| -
| 
| 09013-1C550
| "TORX" Socket Wrench E-type E14
| -
| 
| 09013-7C100
| Straight Hexagon 10mm
| -
| 
| 09017-1C100
| Union Nut Wrench 10mm
| -
| 
| 09051-1C400
| Pin Punch 3
| -
| 
| 09905-00012
| Snap Ring No. 1 Expander
| -
| 
| 09905-00013
| Snap Ring Pliers
| -
| |
|
SSMToyota Genuine seal packing 1281, Three Bond 1281 or equivalent
| -
| Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent
| -
| Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
| -
| |
|