Home › DRIVE LINE › DIFFERENTIAL › DIFFERENTIAL CARRIER ASSEMBLY

DIFFERENTIAL CARRIER ASSEMBLY > REASSEMBLY > Preparation



SST 
I002418
09316-60011
Transmission & Transfer Bearing
Replacer

I002419
(09316-00011)
Replacer Pipe


I002420
(09316-00021)
Replacer A


I002422
(09316-00041)
Replacer C


I000032
09330-00021
Companion Flange Holding Tool


I000883
(09330-00030)
Pin


I000677
09504-00011
Differential Side Bearing
Adjusting Nut Wrench

I000040
09506-30012
Differential Drive Pinion Rear
Bearing Cone Replacer

I000395
09554-30011
Differential Oil Seal Replacer


I000054
09556-22010
Drive Pinion Front Bearing
Remover

I000745
09649-17010
Steering Knuckle Tool


I010020
09930-00010
Drive Shaft Nut Chisel


I010021
(09931-00010)
Handle


I010022
(09931-00020)
Nut Chisel


I002108
09950-30012
Puller A Set


I002109
(09951-03010)
Upper Plate


I002110
(09953-03010)
Center Bolt


I002111
(09954-03010)
Arm


I002142
(09955-03030)
Lower Plate 130


I002146
(09956-03040)
Adapter 22


I002306
09950-60010
Replacer Set


I002333
(09951-00430)
Replacer 43


I002337
(09951-00470)
Replacer 47


I002338
(09951-00480)
Replacer 48


I002345
(09951-00550)
Replacer 55


I002307
09950-70010
Handle Set


I002346
(09951-00560)
Replacer 56


I002347
(09951-00570)
Replacer 57


I002357
(09951-07150)
Handle 150


I002061
09960-10010
Variable Pin Wrench Set


I002062
(09962-01000)
Variable Pin Wrench Arm Assembly


I002064
(09963-00700)
Pin 7




EQUIPMENT
Brass bar
-
Chisel
-
Dial indicator with magnetic base
-
Feeler gauge
-
Hammer
-
Micrometer
-
MP grease
-
Needle nose pliers
-
Plastic hammer
-
Press
-
Red lead
-
Screwdriver
-
Tape
-
Torque wrench
-
Vernier calipers
-


LUBRICANT (2012/01 - 2012/10) / Recommended Viscosity
Item
Temperature
Viscosity
Front Differential
Rear Differential
Above -18°C (0°F)
SAE 90
Below -18°C (0°F)
SAE 80W-90 or SAE 80W

LUBRICANT (2012/01 - 2012/10) / Differential Oil Type
Item
Oil type
Front Differential
Rear Differential
Hypoid gear oil API GL-5

LUBRICANT (2012/01 - 2012/10) / Standard Differential Oil Capacity
Item
Specified Condition
Front Differential
1.40 to 1.50 liters (1.48 to 1.58 US qts., 1.23 to 1.32 Imp. qts.)
Rear Differential
3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.)
w/ Differential Lock
2.85 to 2.95 liters (3.01 to 3.12 US qts., 2.51 to 2.59 Imp. qts.)
4WD, Pre-Runner and made DANA
2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.)


LUBRICANT (2012/10 -        ) / Recommended Viscosity
Item
Temperature
Viscosity
Front Differential
Rear Differential
Above -18°C (0°F)
SAE 90
Below -18°C (0°F)
SAE 80W-90 or SAE 80W

LUBRICANT (2012/10 -        ) / Differential Oil Type
Item
Oil type
Front Differential
Rear Differential
Hypoid gear oil API GL-5

LUBRICANT (2012/10 -        ) / Standard Differential Oil Capacity
Item
Specified Condition
Front Differential
1.40 to 1.50 liters (1.48 to 1.58 US qts., 1.23 to 1.32 Imp. qts.)
Rear Differential
3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.)
4WD, Pre-Runner and made DANA
2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.)


RECOMMENDED TOOLS
I002297
09011-2C590
Socket Wrench
30mm/12p
-
I001236
09013-1C550
"TORX" Socket Wrench E-type
E14
-
I001889
09013-7C100
Straight Hexagon
10mm
-
I102211
09017-1C100
Union Nut Wrench
10mm
-
I000406
09051-1C400
Pin Punch
3
-
I000114
09905-00012
Snap Ring No. 1 Expander
-
I000115
09905-00013
Snap Ring Pliers
-


SSM
Toyota Genuine seal packing 1281, Three Bond 1281 or equivalent
-
Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent
-
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
-