Home
›
DRIVE LINE
›
DIFFERENTIAL
›
DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock)
DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) > REASSEMBLY > Preparation
SST
09308-00010
Oil Seal Puller
09316-60011
Transmission & Transfer Bearing
Replacer
(09316-00011)
Replacer Pipe
(09316-00021)
Replacer A
(09316-00041)
Replacer C
09330-00021
Companion Flange Holding Tool
(09330-00030)
Pin
09504-00011
Differential Side Bearing
Adjusting Nut Wrench
09506-30012
Differential Drive Pinion Rear
Bearing Cone Replacer
09554-30011
Differential Oil Seal Replacer
09556-22010
Drive Pinion Front Bearing
Remover
09930-00010
Drive Shaft Nut Chisel
(09931-00010)
Handle
(09931-00020)
Nut Chisel
09950-30012
Puller A Set
(09951-03010)
Upper Plate
(09953-03010)
Center Bolt
(09954-03010)
Arm
(09955-03030)
Lower Plate 130
(09956-03040)
Adapter 22
09950-60010
Replacer Set
(09951-00430)
Replacer 43
(09951-00470)
Replacer 47
(09951-00480)
Replacer 48
(09951-00550)
Replacer 55
09950-70010
Handle Set
(09951-00560)
Replacer 56
(09951-00570)
Replacer 57
(09951-07150)
Handle 150
09960-10010
Variable Pin Wrench Set
(09962-01000)
Variable Pin Wrench Arm Assembly
(09963-00700)
Pin 7
EQUIPMENT
Brass bar
-
Chisel
-
Dial indicator with magnetic base
-
Feeler gauge
-
Hammer
-
Micrometer
-
MP grease
-
Needle nose pliers
-
Plastic hammer
-
Press
-
Red lead
-
Screwdriver
-
Tape
-
Torque wrench
-
Vernier calipers
-
LUBRICANT / Recommended Viscosity
Item
Temperature
Viscosity
Front Differential
Rear Differential
Above -18°C (0°F)
SAE 90
Below -18°C (0°F)
SAE 80W-90 or SAE 80W
LUBRICANT / Differential Oil Type
Item
Oil type
Front Differential
Rear Differential
Hypoid gear oil API GL-5
LUBRICANT / Standard Differential Oil Capacity
Item
Specified Condition
Front Differential
1.40 to 1.50 liters (1.48 to 1.58 US qts., 1.23 to 1.32 Imp. qts.)
Rear Differential
3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.)
w/ Differential Lock
2.85 to 2.95 liters (3.01 to 3.12 US qts., 2.51 to 2.59 Imp. qts.)
4WD, Pre-Runner and made DANA
2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.)
RECOMMENDED TOOLS
09011-2C590
Socket Wrench
30mm/12p
-
09013-1C550
"TORX" Socket Wrench E-type
E14
-
09013-7C100
Straight Hexagon
10mm
-
09017-1C100
Union Nut Wrench
10mm
-
09051-1C400
Pin Punch
3
-
09905-00012
Snap Ring No. 1 Expander
-
09905-00013
Snap Ring Pliers
-
SSM
Toyota Genuine seal packing 1281, Three Bond 1281 or equivalent
-
Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent
-
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
-