Home › Vehicle Exterior › BODY WELD POINT › FIT STANDARD / ADJUSTMENT METHOD
BM33K0E _01 Vehicle Exterior _046210 BODY WELD POINT _0217948 FIT STANDARD / ADJUSTMENT METHOD F

BODY WELD POINT  FIT STANDARD / ADJUSTMENT METHOD  ADJUSTMENT  


INSPECT HOOD SUB-ASSEMBLY


a.

Check that the clearance measurements of areas A to D are within the standard ranges.

B408864N01
2.635,0.198 2.865,0.448 0.229,0.25 10 false A 2.781,0.615 3.01,0.865 0.229,0.25 10 false B 4.885,0.26 5.115,0.51 0.229,0.25 10 false C 4.708,1.052 4.938,1.302 0.229,0.25 10 false D

Standard:
Area Specified Condition Area Specified Condition
A 4.0 to 7.0 mm (0.157 to 0.276 in.) B -0.6 to 2.4 mm (-0.024 to 0.094 in.)
C 3.5 to 6.5 mm (0.138 to 0.256 in.) D -0.7 to 2.3 mm (-0.028 to 0.091 in.)




HINT:

Centering bolts are used to mount the hood hinge to the vehicle body and hood. The hood cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.


ADJUST HOOD SUB-ASSEMBLY


a.
B408868

Adjust the hood position.

i.

Loosen the 4 hinge bolts on the hood and adjust the hood position.


ii.

Move the hood and adjust the clearance between the hood and front fender.


iii.

Tighten the 4 hinge bolts on the hood after the adjustment.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)



b.
B408869

Adjust the cushion rubbers so that the hood and fender are aligned.

HINT:

Raise or lower the front end of the hood by turning the cushion rubber.



c.
B408870

Adjust the hood lock.

i.

Loosen the 3 bolts.


ii.

Adjust the hood lock position so that the striker can enter it smoothly.


iii.

Tighten the 3 bolts after the adjustment.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)




INSPECT FRONT DOOR PANEL SUB-ASSEMBLY LH


a.

Check that the clearance measurements of areas A to J are within the standard ranges.

B408849N01
1.146,0.26 1.302,0.458 0.156,0.198 10 false A 2.823,0.188 2.979,0.385 0.156,0.198 10 false B 2.99,0.99 3.146,1.188 0.156,0.198 10 false C 5.469,0.198 5.625,0.396 0.156,0.198 10 false D 5.708,0.76 5.865,0.958 0.156,0.198 10 false E 5.896,1.479 6.052,1.677 0.156,0.198 10 false F 6.354,1.708 6.51,1.906 0.156,0.198 10 false G 6.031,2.625 6.188,2.823 0.156,0.198 10 false H 6.51,2.896 6.667,3.094 0.156,0.198 10 false I 1.729,2.5 1.885,2.698 0.156,0.198 10 false J

Standard Clearance:
A 2.8 to 5.8 mm (0.110 to 0.228 in.) B 3.2 to 6.2 mm (0.126 to 0.244 in.)
C 2.2 to 5.2 mm (0.087 to 0.205 in.) D 3.2 to 6.2 mm (0.126 to 0.244 in.)
E 2.5 to 5.5 mm (0.098 to 0.217 in.) F 3.2 to 6.2 mm (0.126 to 0.244 in.)
G -1.5 to 1.5 mm (-0.059 to 0.059 in.) H 3.2 to 6.2 mm (0.126 to 0.244 in.)
I -1.5 to 1.5 mm (-0.059 to 0.059 in.) J 4.2 to 7.2 mm (0.165 to 0.283 in.)




HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the RH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.



ADJUST FRONT DOOR PANEL SUB-ASSEMBLY LH


a.
B408886

Using SST, loosen the hinge bolts on the body and adjust the door position.

SST
09812-00010  


b.

Tighten the hinge bolts on the body after the adjustment.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.
B408830

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B408831

Using a T40 "TORX" socket wrench, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.


f.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)



INSPECT REAR DOOR PANEL SUB-ASSEMBLY LH


a.

Check that the clearance measurements of areas A to F are within the standard ranges.

B409007N01
2.115,0.344 2.333,0.563 0.219,0.219 10 false A 5.719,0.438 5.938,0.656 0.219,0.219 10 false B 6.083,1.49 6.302,1.708 0.219,0.219 10 false C 5.438,1.813 5.656,2.031 0.219,0.219 10 false D 5.469,2.99 5.688,3.208 0.219,0.219 10 false E 2.156,3.031 2.375,3.25 0.219,0.219 10 false F

Standard Clearance:
Area Measurement Area Measurement
A 3.2 to 6.2 mm (0.126 to 0.244 in.) B 3.2 to 6.2 mm (0.126 to 0.244 in.)
C 2.8 to 5.8 mm (0.110 to 0.228 in.) D -1.5 to 1.5 mm (-0.059 to 0.059 in.)
E 4.2 to 7.2 mm (0.165 to 0.283 in.) F 4.2 to 7.2 mm (0.165 to 0.283 in.)




HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.



ADJUST REAR DOOR PANEL SUB-ASSEMBLY LH


a.
B409009

Using SST, loosen the hinge bolts on the body and adjust the door position.

SST
09812-00010  


b.

Tighten the hinge bolts on the body after the adjustment.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.
B409008

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B409010

Using a T40 "TORX" socket wrench, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)



INSPECT BACK DOOR PANEL SUB-ASSEMBLY


a.

Check that the clearance measurements of areas A to F are within the standard ranges.

B408688C01
3.708,0.146 3.865,0.344 0.156,0.198 10 false A 5.615,0.125 5.771,0.323 0.156,0.198 10 false B 4.802,0.25 4.958,0.448 0.156,0.198 10 false C 6.458,1.802 6.615,2 0.156,0.198 10 false D 5.969,2.833 6.125,3.031 0.156,0.198 10 false E 3.229,3.219 3.385,3.417 0.156,0.198 10 false F

Standard Clearance:
A 6.0 to 9.0 mm (0.236 to 0.354 in.) B 6.0 to 9.0 mm (0.236 to 0.354 in.)
C -0.5 to 2.5 mm (-0.020 to 0.098 in.) D
(Reference)
5.4 mm (0.213 in.)
E
(Reference)
5.6 mm (0.220 in.) F
(Reference)
8.1 mm (0.319 in.)




HINT:

Centering bolts are used to mount the back door hinge to the vehicle body and back door. The back door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts (with washers) when making adjustments.


ADJUST BACK DOOR PANEL SUB-ASSEMBLY


a.
B408689

Before adjusting the upper end of the back door up and down or left and right, loosen the bolts.


b.

Tighten the hinge bolts on the body after the adjustment.

Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)


c.
B408690

Using a T40 "TORX" socket wrench, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.


d.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after the adjustment.

Torque:
23.5 N*m (240 kgf*cm, 17 ft.*lbf)