Home › Vehicle Exterior › BODY WELD POINT › FRONT BODY PILLAR
BM33K0E _01 Vehicle Exterior _046210 BODY WELD POINT _0223718 FRONT BODY PILLAR F

BODY WELD POINT  FRONT BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS  


K125162

With the cowl top side upper panel assembly and cowl top side panel assembly removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location

K123775

K123776C01
1.542,0.656 1.854,0.813 0.313,0.156 10 false *a 5.365,0.479 5.677,0.635 0.313,0.156 10 false *b 5.031,0.635 5.344,0.792 0.313,0.156 10 false *c
*a 105 mm (4.13 in.) *b 135 mm (5.31 in.)
*c 65 mm (2.56 in.) - -


a.

Be careful when cutting as foamed sealing material is located near the cutting position.

HINT:

Remove the remaining foamed sealing material from the vehicles side.


K123777C01
3.844,0.99 4.156,1.146 0.313,0.156 10 false *a
*a 200 mm (7.87 in.) - -
K108840

Foamed Sealing Material - -




INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

If the entire supply part is not needed, remove the part of the supply part that is needed.

HINT:

Carefully cut the rocker panel outer so not to damage A.


K125197C01
0.5,1.25 0.667,1.25 0.667,1.25 0.917,1.833 false 5.417,2.333 5.583,2.333 5.583,2.333 5.917,1.917 false 0.583,2.583 0.75,2.583 0.75,2.583 1,2.052 false 0.417,2.51 0.729,2.667 0.313,0.156 10 false *1 5.26,2.25 5.573,2.406 0.313,0.156 10 false *2 1.438,1.271 1.75,1.427 0.313,0.156 10 false *a 0.333,1.167 0.583,1.333 0.25,0.167 10 false A 5.104,1.26 5.417,1.417 0.313,0.156 10 false *a
*1 ROCKER PANEL OUTER *2 FRONT BODY PILLAR SUB-ASSEMBLY
*a 200 mm (7.87 in.) - -



d.

Before temporarily installing the new parts, weld the rocker panel outer, front body pillar reinforce sub-assembly lower and front body pillar sub-assembly with the standard number of welding points.

K123784C01
2.667,3.25 2.5,3.25 2.5,3.25 2.292,2.844 false 2.177,0.76 2,0.25 2,0.25 2.167,0.25 false 5.656,1.344 5.917,0.917 5.917,0.917 6.083,0.917 false 2.708,3.167 3.021,3.323 0.313,0.156 10 false *1 2.198,0.167 2.51,0.323 0.313,0.156 10 false *2 6.125,0.823 6.438,0.979 0.313,0.156 10 false *3 6.313,2.115 6.625,2.271 0.313,0.156 10 false *a 5.521,3.427 5.833,3.583 0.313,0.156 10 false *b
*1 ROCKER PANEL OUTER *2 FRONT BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER
*3 FRONT BODY PILLAR SUB-ASSEMBLY - -
*a 12 mm (0.47 in.) *b 15 mm (0.59 in.)



e.

Weld the rocker panel outer, front body pillar reinforce sub-assembly lower and front body pillar sub-assembly to the vehicle side.

K123780C01
1.365,2.083 1.667,1.75 1.667,1.75 1.833,1.75 false 0.917,4.083 1.083,4.083 1.083,4.083 1.25,3.448 false 4.333,2 4.5,2 4.5,2 4.76,1.656 false 0.75,4 1.063,4.156 0.313,0.156 10 false *1 1.865,1.667 2.177,1.823 0.313,0.156 10 false *2 4.177,1.917 4.49,2.073 0.313,0.156 10 false *3 4.656,4.167 4.969,4.323 0.313,0.156 10 false *a
*1 ROCKER PANEL OUTER *2 FRONT BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER
*3 FRONT BODY PILLAR SUB-ASSEMBLY - -
*a 15 mm (0.59 in.) - -



f.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K123781


g.

Weld the front body pillar upper outer and front fender bracket rear to the vehicle side.

K123785C01
5.583,4.417 5.75,4.417 5.75,4.417 6.083,3.802 false 2.25,0.813 2.083,0.333 2.083,0.333 1.917,0.333 false 1.76,0.26 2.073,0.417 0.313,0.156 10 false *1 5.427,4.344 5.74,4.5 0.313,0.156 10 false *2
*1 FRONT BODY PILLAR UPPER OUTER *2 FRONT FENDER BRACKET REAR



h.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


i.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


j.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.