Home › Vehicle Exterior › BODY WELD POINT › QUARTER PANEL
BM33K0E _01 Vehicle Exterior _046210 BODY WELD POINT _0223723 QUARTER PANEL F

BODY WELD POINT  QUARTER PANEL  CUT AND JOIN REPLACEMENT SECTIONS  


K125169

REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

a.

Be careful when cutting as foamed sealing material is located near the cutting position.

HINT:

Remove the remaining foamed sealing material from the vehicles side.


K125217C01
0,0 0,0 false
K108840

Foamed Sealing Material - -


K125218C01
2.844,1.24 3.156,1.396 0.313,0.156 10 false *a 5.052,1.26 5.365,1.417 0.313,0.156 10 false *b
*a 255 mm (10.04 in.) *b 30 mm (1.18 in.)


K125219



INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld
K108834

Body Sealer

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

If the entire supply part is not needed, remove the part of the supply part that is needed.

K125220C01
3.5,3.167 3.333,3.167 3.333,3.167 3.083,2.646 false 3.542,3.083 3.854,3.24 0.313,0.156 10 false *1 2.604,1.26 2.917,1.417 0.313,0.156 10 false *a 5.417,0.583 5.729,0.74 0.313,0.156 10 false *b
*1 QUARTER PANEL - -
*a 255 mm (10.04 in.) *b 30 mm (1.18 in.)



d.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


K125221


e.

Before temporarily installing the new parts, weld the quarter panel and fuel inlet box with the standard number of welding points.

K125222C01
3.5,2.833 3.333,2.833 3.333,2.833 3.083,2.406 false 2.333,1.917 2.167,1.917 2.167,1.917 2.125,1.646 false 3.552,2.76 3.865,2.917 0.313,0.156 10 false *1 2.375,1.844 2.688,2 0.313,0.156 10 false *2
*1 QUARTER PANEL *2 FUEL INLET BOX



f.

Before installing a new part, apply body sealer.

HINT:
·

Apply body sealer evenly about 5 mm (0.20 in.) from the flange, avoiding any oozing.

·

Apply body sealer evenly, about 3 to 4 mm (0.12 to 0.16 in.) in diameter.



K125223C01
5.552,1.823 5.865,1.979 0.313,0.156 10 false *a
*a 5 mm (0.20 in.) - -


K125224

K125225


g.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


h.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


i.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.