Home › Vehicle Exterior › BODY WELD POINT › FRAME REAR FRONT CROSSMEMBER
BM33K0E _01 Vehicle Exterior _046210 BODY WELD POINT _0223742 FRAME REAR FRONT CROSSMEMBER F

BODY WELD POINT  FRAME REAR FRONT CROSSMEMBER  ASSEMBLY REPLACEMENT  


K125189

With the frame rear crossmember assembly removed.


K125306

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the RH side.



REMOVAL


Symbol Meaning
K108826

Cut with Disc Sander etc.

K125307C01
1.865,0.615 2.177,0.771 0.313,0.156 10 false *A 2.229,0.25 2.542,0.406 0.313,0.156 10 false *B 2.229,2.677 2.542,2.833 0.313,0.156 10 false *C 1.865,3.052 2.177,3.208 0.313,0.156 10 false *A
*A FRONT *B UPPER
*C LH - -


K125308C01
2.208,0.521 2.521,0.677 0.313,0.156 10 false *A 2.594,0.896 2.906,1.052 0.313,0.156 10 false *B
*A FRONT *B UPPER


K125309C01
2.052,0.771 2.365,0.927 0.313,0.156 10 false *A 1.677,0.396 1.99,0.552 0.313,0.156 10 false *B 1.677,3.125 1.99,3.281 0.313,0.156 10 false *C 2.063,3.521 2.375,3.677 0.313,0.156 10 false *A
*A FRONT *B UPPER
*C RH - -



INSTALLATION


Symbol Meaning
K108830

Fillet Weld

a.

Make sure that proper welding can be performed by setting up the welding conditions as necessary before performing work.


b.

To prevent heat deformation, weld the right and left side of each part before continuing to the next part.


c.

Make sure that the welding bead at A is overlapped.

K125310C01
4.74,1.677 5.167,1.333 5.167,1.333 5.417,1.333 false 3.604,1.406 4,0.417 4,0.417 4.25,0.417 false 3.438,4.01 3.167,4.5 3.167,4.5 2.917,4.5 false 4.76,4.01 5,4.5 5,4.5 5.25,4.5 false 1.854,3.063 2.167,3.219 0.313,0.156 10 false *A 2.229,0.26 2.542,0.417 0.313,0.156 10 false *B 2.24,2.677 2.552,2.833 0.313,0.156 10 false *C 4.844,2.563 5.156,2.719 0.313,0.156 10 false *a 4.781,0.813 5.094,0.969 0.313,0.156 10 false *b 2.896,1.958 3.208,2.115 0.313,0.156 10 false *c 1.854,0.615 2.167,0.771 0.313,0.156 10 false *A 5.469,1.25 5.781,1.406 0.313,0.156 10 false A 4.302,0.333 4.615,0.49 0.313,0.156 10 false A 2.781,4.417 3.094,4.573 0.313,0.156 10 false A 5.313,4.417 5.625,4.573 0.313,0.156 10 false A 1.958,1.51 2.271,1.667 0.313,0.156 10 false *c 2.104,1.125 2.417,1.281 0.313,0.156 10 false *c 2.24,3.615 2.552,3.771 0.313,0.156 10 false *c
*A FRONT *B UPPER
*C LH - -
*a 47 mm (1.85 in.) *b 656 mm (25.83 in.)
*c 5 +/- 5 mm (0.20 +/- 0.20 in.) - -



d.

Make sure that the welding bead at A is overlapped.

K125311C01
4.5,3.25 4.25,3.25 4.25,3.25 3.917,2.365 false 2.208,0.521 2.521,0.677 0.313,0.156 10 false *A 2.604,0.917 2.917,1.073 0.313,0.156 10 false *B 4.563,3.177 4.875,3.333 0.313,0.156 10 false A
*A FRONT *B UPPER



e.

Make sure that the welding bead at A is overlapped.

K125312C01
4.51,3.667 4.917,3.25 4.917,3.25 5.167,3.25 false 3.458,0.979 3.583,0.5 3.583,0.5 3.833,0.5 false 2.354,1.76 1.917,1.333 1.917,1.333 1.667,1.333 false 2.042,0.771 2.354,0.927 0.313,0.156 10 false *A 1.677,0.396 1.99,0.552 0.313,0.156 10 false *B 1.688,3.115 2,3.271 0.313,0.156 10 false *C 5.219,3.167 5.531,3.323 0.313,0.156 10 false *1 2.417,0.74 2.729,0.896 0.313,0.156 10 false *a 2.417,2.667 2.729,2.823 0.313,0.156 10 false *b 3,5.365 3.313,5.521 0.313,0.156 10 false *c 3.042,0.823 3.354,0.979 0.313,0.156 10 false *d 3.344,5.031 3.656,5.188 0.313,0.156 10 false *e 2.063,3.51 2.375,3.667 0.313,0.156 10 false *A 5.135,1.667 5.448,1.823 0.313,0.156 10 false *d 4.135,2.063 4.448,2.219 0.313,0.156 10 false *d 1.833,2.01 2.146,2.167 0.313,0.156 10 false *d 2.646,5.031 2.958,5.188 0.313,0.156 10 false *e 3.885,0.427 4.198,0.583 0.313,0.156 10 false A 1.531,1.25 1.844,1.406 0.313,0.156 10 false A
*A FRONT *B UPPER
*C RH - -
*1 FRAME CROSSMEMBER SUB-ASSEMBLY NO.6 - -
*a 358 mm (14.09 in.) *b 47 mm (1.85 in.)
*c 70 mm (2.76 in.) *d 5 +/- 5 mm (0.20 +/- 0.20 in.)
*e 3 +/- 5 mm (0.12 +/- 0.20 in.) - -



f.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.