Home › Engine / Hybrid System › 1KD-FTV ENGINE MECHANICAL › ENGINE UNIT
NM33K0E _51 Engine / Hybrid System _043756 1KD-FTV ENGINE MECHANICAL _0204742 ENGINE UNIT GE GENERAL F

1KD-FTV ENGINE MECHANICAL  ENGINE UNIT  GENERAL  GENERAL  


OUTLINE


a.

The 1KD-FTV TOYOTA Direct injection 4 stroke common-rail Diesel engine (D-4D) is an in-line 4-cylinder, 3.0-liter, 16-valve DOHC, turbocharged diesel engine with intercooler. This engine uses the direct injection system and common-rail system to achieve high performance, clean emissions, low noise and low vibrations.


b.

An intercooler is provided. This lowers the intake air temperature and improves power output.



SPECIFICATION


No. of Cyls. and Arrangement 4-cylinder, In-line
Valve Mechanism 16-valve DOHC, Belt and Gear Drive
Combustion Chamber Direct Injection Type
Manifolds Cross-flow
Fuel System Common-rail Type
Displacement 2982 cm3 (182.0 cu. in.)
Bore x Stroke 96.0 mm x 103.0 mm (3.78 in. x 4.06 in.)
Compression Ratio 17.9 : 1
Max. Output (EEC) 120 kW @ 3400 rpm
Max. Torque (EEC) M/T 343 N*m @ 1400 to 3200 rpm
A/T 360 N*m @ 1600 to 3000 rpm
Valve Timing Intake Open 2° BTDC
Closed 37° ABDC
Exhaust Open 45° BBDC
Closed 0° ATDC
Firing Order 1 - 3 - 4 - 2
Fuel Cetane Number 48 or higher
Emission Regulation -
Engine Service Mass (Reference)* M/T 261 kg (575 lb)
A/T 251 kg (553 lb)

*: Weight shows the figure with oil and coolant fully filled.



MAIN FEATURES


a.

This engine has been able to achieve the following performance through the use of the items listed below:

A: High performance and fuel economy

B: Low noise and vibration

C: Lightweight and compact design

D: Good serviceability

E: Clean emissions

Item A B C D E
Engine Proper A cylinder head cover sub-assembly made of plastic is used. - - ○ - -
A cylinder head sub-assembly made of aluminum alloy is used. - - ○ - -
A piston provided with combustion chamber is used. ○ ○ - - ○
2 balance shafts are used. - ○ - - -
Valve Mechanism An intake camshaft is driven by a timing belt, and an exhaust camshaft is driven by a gear. - ○ ○ - -
An automatic tensioner (No. 1 chain tensioner assembly) is provided for the timing belt. - - - ○ -
Cooling System Toyota Genuine Super Long Life Coolant (SLLC) is used. - - - ○ -
Intake and Exhaust System A diesel throttle valve is used. ○ ○ - - ○
A swirl control valve is used. ○ ○ - - ○
A variable nozzle vane type turbocharger is used. ○ - - - ○
An intercooler assembly is used. ○ - - - ○
Fuel System An HP3 type supply pump assembly is used. ○ ○ ○ - -
A common-rail type fuel injection system is used. ○ ○ - - ○
An injector assembly is provided in the bore center. ○ ○ - - ○
Compensation values and Quick Response (QR) codes are used. ○ ○ - - ○
A fuel cooler is used. ○ - - - -
Serpentine Belt Drive System A serpentine belt drive system is used. - - - ○ -
Engine Control System An intake mass air flow meter sub-assembly is used. ○ - - - ○
Non-contact sensors are used as the accelerator pedal sensor assembly and diesel throttle valve position sensor. ○ - - - ○
A pilot injection control system is used. - ○ - - ○
A swirl control is used. ○ - - - -


HINT:

○: Available

-: Not available