Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM
NM33K0E _51 Engine / Hybrid System _045489 2TR-FE ENGINE CONTROL _0213939 SFI SYSTEM DE DETAILS F

2TR-FE ENGINE CONTROL  SFI SYSTEM  DETAILS  CAMSHAFT POSITION SENSOR  


CONSTRUCTION


a.

Magnetic Resistance Element (MRE) type intake and exhaust cam position sensors are used.


b.

To detect each camshaft position, a timing rotor that is secured to the intake camshaft in front of the VVT-i controller and installed on the exhaust camshaft is used to generate 3 high output and 3 low output signals for every 2 revolutions of the crankshaft.

W126160C01
4.771,0.729 5.083,0.49 true 4.833,1.323 5.844,1.729 true 2.469,1.167 3.427,1.99 true 2.177,3.177 3.24,3.042 true 2.333,1.031 2.646,1.188 0.313,0.156 10 false *1 2.021,3.063 2.333,3.219 0.313,0.156 10 false *2 5.875,1.656 6.188,1.813 0.313,0.156 10 false *3 5.073,0.333 5.385,0.49 0.313,0.156 10 false *4
*1 Timing Rotor (Intake) *2 Cam Position Sensor (Intake)
*3 Timing Rotor (Exhaust) *4 Cam Position Sensor (Exhaust)


Sensor Output Waveforms
W126161E01
3.146,0.448 3.896,0.771 0.75,0.323 10 false 720° CA 4.656,0.885 5.406,1.208 0.75,0.323 10 false 180° CA 3.635,0.896 4.385,1.219 0.75,0.323 10 false 120° CA 2.594,0.896 3.344,1.219 0.75,0.323 10 false 60° CA 0.792,1 1.542,1.323 0.75,0.323 10 false High 0.792,1.615 1.542,1.938 0.75,0.323 10 false Low 1.927,1.771 2.677,2.094 0.75,0.323 10 false 180° CA 2.979,1.771 3.729,2.094 0.75,0.323 10 false 120° CA 4.115,1.771 4.865,2.094 0.75,0.323 10 false 60° CA 2.365,2.448 3.115,2.771 0.75,0.323 10 false 360° CA 4.26,2.448 5.01,2.771 0.75,0.323 10 false 360° CA


c.

The MRE type cam position sensor consists of an MRE, a magnet and a sensor. The direction of the magnetic field changes due to the different shapes (protruded and non-protruded portions) of the timing rotor, which passes by the sensor. As a result, the resistance of the MRE changes, and the output voltage to the ECM changes to high or low. The ECM detects the cam position based on this output voltage.


d.

The differences between the MRE type sensor and the pick-up coil type sensor are as follows:

i.

The MRE type sensor outputs a constant level of high and low digital signals regardless of the engine speed. Therefore, the MRE type sensor can detect the positions of the crankshaft and camshaft at an early stage of cranking.


ii.

The pick-up coil type sensor outputs analog signals with levels that change with the engine speed.

MRE Type and Pick-up Coil Type Output Waveform Image Comparison
W126162E01
4.552,1 4.292,0.5 4.292,0.5 4.438,0.5 true 4.281,1.75 4.135,2.271 4.135,2.271 4.26,2.271 true 0.396,0.156 0.875,0.698 0.479,0.542 10 false Engine Speed 0.406,1.552 0.885,2.094 0.479,0.542 10 false Sensor Output 4.5,0.385 5.927,0.833 1.427,0.448 10 false No Detection Area 4.313,2.177 5.74,2.625 1.427,0.448 10 false No Detection Area 5.833,1.833 6.833,2.302 1,0.469 10 false Analog Output 4.5,2.417 5.667,2.75 1.167,0.333 10 false Pick-up Coil Type 1.573,2.427 2.271,2.792 0.698,0.365 10 false MRE Type 3.458,1.552 3.938,2.094 0.479,0.542 10 false Sensor Output 3.438,0.156 3.917,0.698 0.479,0.542 10 false Engine Speed 2.5,1.792 3.406,2.146 0.906,0.354 10 false Digital Output