Home › Engine / Hybrid System › 1GD-FTV ENGINE MECHANICAL › ENGINE UNIT
NM33K0E _51 Engine / Hybrid System _046122 1GD-FTV ENGINE MECHANICAL _0217547 ENGINE UNIT GE GENERAL F

1GD-FTV ENGINE MECHANICAL  ENGINE UNIT  GENERAL  GENERAL  


OUTLINE


a.

The 1GD-FTV TOYOTA Direct injection 4 stroke common-rail Diesel engine (D-4D) is an in-line 4-cylinder, 2.8-liter, 16-valve DOHC, turbocharged diesel engine. This engine uses the direct injection system and common-rail system to achieve high performance, clean emissions, low noise and low vibrations.


b.

An intercooler is provided. This lowers the intake air temperature and improves power output.



SPECIFICATION


Engine Type 1GD-FTV
w/ Variable Nozzle Vane Type Turbocharger
w/ Solenoid Type Injector
No. of Cyls. and Arrangement 4-cylinder, In-line
Valve Mechanism 16-valve DOHC, Chain Drive
Combustion Chamber Direct Injection Type
Manifolds Cross-flow
Fuel System Common-rail Type
Displacement 2755 cm3 (168.1 cu. in.)
Bore x Stroke 92.0 mm x 103.6 mm (3.62 in. x 4.08 in.)
Compression Ratio 15.6 : 1
Max. Output (EEC) 130 kW @ 3400 rpm
Max. Torque (EEC) 420 N*m @ 1400 to 2600 rpm*1
450 N*m @ 1600 to 2400 rpm*2
Valve Timing Intake Open 6°BTDC
Closed 29°ABDC
Exhaust Open 40°BBDC
Closed 10°ATDC
Firing Order 1 - 3 - 4 - 2
Fuel Cetane Number 48 or higher
Emission Regulation*4 EURO 4
EURO 5
Tier 1.5
Engine Service Mass (Reference)*5 270 kg*1
263 kg*2
255 kg*3

HINT:

*1: Models with manual transmission

*2: Models with automatic transmission (except models compliant with Tier 1.5 emission regulations)

*3: Models with automatic transmission (models compliant with Tier 1.5 emission regulations)

*4: Emission regulation differ by country and region.

*5: Weight shows the figure with oil and water fully filled.



MAIN FEATURES


a.

This engine is able to achieve the following through the use of the items listed below:

(1) High performance and fuel economy

(2) Low noise and vibration

(3) Lightweight and compact design

(4) Good serviceability

(5) Clean emissions


Item (1) (2) (3) (4) (5)

*: Models with catalyst support control

A cylinder head cover sub-assembly made of plastic is used. - ○ ○ - -
An oil mist separator is used on the cylinder head cover sub-assembly. - - - - ○
A cylinder head sub-assembly made of aluminum alloy is used. - - ○ - -
A tangential port and a helical port are used on the intake port. ○ - - - ○
A piston provided with a combustion chamber is used. ○ ○ - - ○
Connecting rod sub-assemblies made of high tension material. ○ ○ ○ - -
A timing chain and a chain tensioner are used. - ○ - ○ -
Valve lash adjuster assemblies are used. - ○ - ○ -
Valve rocker arm sub-assemblies are used. ○ ○ ○ ○ -
Toyota Genuine Super Long Life Coolant (SLLC) is used. - - - ○ -
A serpentine belt drive system is used. - - ○ ○ -
A diesel throttle valve is used. ○ ○ - - ○
A variable nozzle vane type turbocharger sub-assembly is used. ○ - - - ○
An intercooler assembly is used. ○ - - - ○
An HP5S type injection or supply pump assembly is used. ○ ○ ○ - ○
A common-rail type fuel injection system is used. ○ ○ - - ○
An injector assembly is provided in the bore center. ○ ○ - - ○
Compensation values and Quick Response (QR) codes are used. ○ - - ○ ○
An intake mass air flow meter sub-assembly is used. ○ - - - ○
A pilot injection control system is used. - ○ - - ○
An EGR system is used. - - - - ○
An EGR cooler with bypass is used. - - - - ○
An oxidation catalyst is used. - - - - ○
A DPF is used.* - - - - ○