OUTLINE
An automatic air conditioning system or a manual air conditioning system is used depending on models.
The automatic air conditioning system uses neural network control to enhance comfort.
The rear cooling unit assembly is mounted inside the deck side trim.
An automatic rear cooler system or a manual rear cooler system is used.
SPECIFICATIONS
Front Air Conditioning
| Item | Specifications | ||
|---|---|---|---|
| Automatic Air Conditioning System | Manual Air Conditioning System | ||
|
*1: Models with 2TR-FE, 1GR-FE, 1GD-FTV engine *2: Models with 1KD-FTV engine |
|||
| Blower Motor with Fan Sub-assembly | Motor Type | 4 Pole Motor | |
| Fan Type | Semi-sirocco | ||
| Fan Size (Dia. x H) | 137 mm x 70 mm (5.4 in. x 2.8 in.) | ||
| Cooler Condenser Assembly (Global Inner-fin Condenser (GIC) Type) | Size (W x H x D) | 580 mm x 517 mm x 11.5 mm (22.8 in. x 20.4 in. x 0.5 in.) | |
| Fin Pitch | 3.0 mm (0.11 in.) | ||
| Cooler Condenser Assembly (Parallel Flow Condenser (PFC) Type) | Size (W x H x D) | 570mm x 509.4mm x 16mm x (22.4in x 20.1in x 0.6in) | |
| Fin Pitch | 2.8mm (0.11in) | ||
| No. 1 Cooler Evaporator Sub-assembly | Type | Beneficial Refrigerant Stream (BRS) | |
| Size (W x H x D) | 231 x 239.5 x 38 (9.1 in. x 9.4 in. x 1.5 in.) | ||
| Fin Pitch | 3.0 mm (0.12 in.) | ||
| Heater Radiator Unit Sub-assembly | Type | Straight Flow Aluminum (SFA)-II | |
| Size (W x H x D) | 222.3 mm x 120 mm x 27 mm (8.8 in. x 4.7 in. 1.1 in.) | ||
| Fin Pitch | 1.8 mm (0.07 in.) | ||
| Cooler Compressor Assembly | Type | 10SRE15C*1, 10S15C*2 | |
| Refrigerant | Type | HFC-134a (R-134a) | |
| Charge Volume | 750 g | ||
Rear Cooler
| Item | Specifications | |
|---|---|---|
| Blower Motor with Fan Sub-assembly | Motor Type | 4 Pole Motor |
| Fan Type | Semi-sirocco | |
| Fan Size (Dia. x H) | 150 mm x 75 mm (5.9 in. x 3.0 in.) | |
| Cooler Evaporator Sub-assembly | Type | Revolutionary super-slim Structure (RS) Type |
| Size (W x H x D) | 118.9 mm x 251 mm x 38 mm (4.7 in x 9.9 in. x 1.5 in.) | |
| Fin Pitch | 3.0 mm (0.11 in.) | |
MAIN FEATURES
The air conditioning system has the following features:
| Feature | Outline |
|---|---|
|
*: Models with automatic air conditioning system |
|
| High Performance | ·
Neural network control is used, so passengers can finely control the air conditioning for maximum comfort.* ·
The rear cooling unit assembly is available on all models. ·
A clean air filter (air refiner element) is used. ·
The blower control has 7 levels in manual mode and 31 levels in auto mode for more precise control.* |
| Light Weight* | ·
A bus connector with a built-in IC is used in a lightweight wire harness design to allow for a reduced number of wires. ·
The use of this connector means that pulse pattern type servo motors can be used. |
| Others | The following parts are used to ensure high cooling performance while achieving a compact and lightweight construction:
·
Semi-center Location Air Conditioning Unit ·
Beneficial Refrigerant Stream (BRS) Evaporator ·
Straight Flow Aluminum (SFA)-II Heater Radiator Sub-assembly ·
Global Inner-fin Condenser (GIC) |