Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM
NM33K0E _56 Audio / Visual / Telematics _047964 PARK ASSIST / MONITORING _0227368 TOYOTA PARKING ASSIST-SENSOR SYSTEM CO CONTROL F

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  CONTROL  TOYOTA PARKING ASSIST-SENSOR CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The components have the following functions:

Component Function

*1: Models with automatic transmission

*2: Models with manual transmission

No. 1 Ultrasonic Sensor Detects the distance between the vehicle and on obstacle.
No. 1 Clearance Warning Buzzer Sounds to inform the driver according to the distance to the obstacle.
Clearance Warning ECU Assembly
·

Judges the approximate distance between the vehicle and an obstacle based on signals from the No. 1 ultrasonic sensors.

·

Sounds the No. 1 clearance warning buzzer.


Back Sonar or Clearance Sonar Switch Assembly Operating this switch allows the operation of Toyota parking assist-sensor system to be enabled or disabled.
Park/ Neutral Position Switch Assembly*1 Transmits the shift position signal to the clearance warning ECU assembly.
Back-up Light Switch Assembly*2 Transmits the on/off signal of the back-up light switch assembly to the clearance warning ECU assembly.



OPERATING CONDITION


a.

The operating condition of each sensor differs according to its installed position as shown in the table below:

Installation Position Operating Condition
Rear Center
·

Ignition switch is ON.

·

Back sonar or clearance sonar switch assembly is on.

·

Shift lever is in R.





SYSTEM CONTROL


a.

No. 1 Clearance Warning Buzzer

i.

The on and off times of the No. 1 clearance warning buzzer vary as shown in the table below, depending on the distance between the obstacle and the ultrasonic sensor:

Ultrasonic Sensor Obstacle Distance [mm (in.)] Off Time (ms) On Time (ms)
Detection Level Longest 1500 +/- 150 to 600 +/- 60 (59.1 +/- 5.91 to 23.6 +/- 2.36) 500 +/- 50 200 +/- 20
Long 600 +/- 60 to 450 +/- 50 (23.6 +/- 2.36 to 17.7 +/- 1.97) 200 +/- 20 200 +/- 20
Middle 450 +/- 50 to 350 +/- 40 (17.7 +/- 1.97 to 13.8 +/- 1.57 ) 100 +/- 10 100 +/- 10
Short 350 +/- 40 or less (13.8 +/- 1.57 or less) 0 Continuous

Y185918E01
0.583,0.844 2.125,1.135 1.542,0.292 10 false Short-range Detection 0.594,2.208 2.135,2.5 1.542,0.292 10 false Middle-range Detection 0.583,3.521 2.125,3.813 1.542,0.292 10 false Long-range Detection 0.573,4.906 2.115,5.198 1.542,0.292 10 false Longest-range Detection 2.417,0.625 2.917,0.917 0.5,0.292 10 false On 2.417,1.125 2.917,1.417 0.5,0.292 10 false Off 2.417,1.99 2.917,2.281 0.5,0.292 10 false On 2.417,2.469 2.917,2.76 0.5,0.292 10 false Off 2.417,3.333 2.917,3.625 0.5,0.292 10 false On 2.417,3.813 2.917,4.104 0.5,0.292 10 false Off 2.417,5.167 2.917,5.458 0.5,0.292 10 false Off 2.417,4.667 2.917,4.958 0.5,0.292 10 false On 3.031,1.677 3.531,1.969 0.5,0.292 10 false *a 3.302,1.667 3.802,1.958 0.5,0.292 10 false *a 3.135,3.021 3.635,3.313 0.5,0.292 10 false *b 3.677,3.021 4.177,3.313 0.5,0.292 10 false *b 3.167,4.396 3.667,4.688 0.5,0.292 10 false *b 3.979,4.375 4.479,4.667 0.5,0.292 10 false *c 0.167,5.75 2.667,6.042 2.5,0.292 10 false *a: Approximately 0.1 seconds 0.167,6.115 2.667,6.406 2.5,0.292 10 false *b: Approximately 0.2 seconds 0.167,6.458 2.667,6.75 2.5,0.292 10 false *c: Approximately 0.5 seconds


ii.

When a malfunction is detected, the No. 1 clearance warning buzzer continues to sound as shown in the illustration.

Y185917E01
3.063,0.51 5.49,0.76 2.427,0.25 10 false Approximately 1.5 seconds (1 cycle) 0.125,1.156 1.135,1.552 1.01,0.396 10 false Approximately 0.25 seconds 3.042,1.146 4.167,1.542 1.125,0.396 10 false Approximately 0.75 seconds 5.573,1.146 6.698,1.542 1.125,0.396 10 false Returns to Normal 1.042,1.854 1.365,2.167 0.323,0.313 10 false On 1.031,2.125 1.354,2.438 0.323,0.313 10 false Off



b.

Detection Area

i.

The detection areas of the No. 1 ultrasonic sensors are as shown in the following illustration.


ii.

These detection areas are applicable when positioning a 60 mm (2.36 in.) diameter pole parallel or perpendicular to the ground. The ranges vary depending on the measuring method and type of obstacle.

Y177334C01
6,0.24 6.313,0.438 0.313,0.198 10 false *a 6.448,1.458 6.76,1.656 0.313,0.198 10 false *b 5.333,2.667 5.646,2.865 0.313,0.198 10 false *c 5.406,3.063 5.719,3.26 0.313,0.198 10 false *d 5.99,4.5 6.302,4.698 0.313,0.198 10 false *e 4.958,5.417 5.271,5.615 0.313,0.198 10 false *f 0.073,5.563 0.385,5.76 0.313,0.198 10 false *g
*a Wall *b Approximately 1720 mm (67.7 in.)
*c Approximately 1000 mm (39.4 in.) *d Approximately 1500 mm (59.1 in.)
*e Approximately 550 mm (21.6 in.) *f Approximately 100 mm (3.9 in.)
*g The illustrations shown are examples only. - -