Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM33K0E _57 Power Source / Network _043546 NETWORKING _0208242 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2786  No Response from Steering Lock ECU  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and steering lock actuator or upper bracket assembly stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2786 No Response from Steering Lock ECU Communication between the certification ECU (smart key ECU assembly) and steering lock or upper bracket assembly stops for 10 seconds or more.
·

Steering lock actuator or upper bracket assembly

·

Certification ECU (smart key ECU assembly)

·

Harness or connector



WIRING DIAGRAM

B403440E01
0.875,1.667 2.677,2.042 1.802,0.375 10 false Certification ECU (Smart Key ECU Assembly) 4.427,4.063 6.417,4.448 1.99,0.385 10 false Steering Lock Actuator or Upper Bracket Assembly 4.427,3.885 4.885,4.083 0.458,0.198 10 false G19 5.625,3.333 6.083,3.531 0.458,0.198 10 false GND 6.042,3.219 6.198,3.417 0.156,0.198 10 false 1 1.771,2.469 2.604,2.698 0.833,0.229 10 false from Battery 1.646,3.219 2.635,3.438 0.99,0.219 10 false from IG2 Relay 3.531,3.406 4.198,3.625 0.667,0.219 10 false IG2 NO.2 3.083,2.667 4.646,2.917 1.563,0.25 10 false STRG LOCK/AM2 NO.1 0.667,4.292 2.323,4.49 1.656,0.198 10 false : LIN Communication Line 0.875,1.49 1.333,1.688 0.458,0.198 10 false G16 4.958,0.896 5.417,1.094 0.458,0.198 10 false LIN 2.146,0.896 2.604,1.094 0.458,0.198 10 false LIN 2.458,0.719 2.615,0.917 0.156,0.198 10 false 5 4.729,0.729 4.885,0.927 0.156,0.198 10 false 5 4.75,3.125 4.906,3.323 0.156,0.198 10 false 6 4.948,3.219 5.406,3.417 0.458,0.198 10 false IG2 4.74,2.365 4.896,2.563 0.156,0.198 10 false 7 4.948,2.469 5.104,2.667 0.156,0.198 10 false B

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

If the certification ECU (smart key ECU assembly) or steering actuator assembly is replaced, refer to the Service Bulletin.



HINT:

When the communication between the steering lock actuator assembly and certification ECU (smart key ECU assembly) stops, DTC B2785 is also stored.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2786 is output
DTC B2786 is not output



DTC B2786 is output

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

DTC B2786 is not output

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the G19 steering lock actuator or upper bracket assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-5 (LIN) - G19-5 (LIN) Always Below 1 Ω
G16-5 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY - BATTERY AND BODY GROUND)
B291261C10
1.521,0.354 1.875,0.594 0.354,0.24 0.75,1.656 1.167,1.24 false 2.76,0.906 2.302,1.208 false 2.271,1.844 2.052,1.271 false 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 0.406,1.594 0.865,1.792 0.458,0.198 10 false GND 2.833,0.823 2.99,1.021 0.156,0.198 10 false B 1.573,0.385 1.885,0.583 0.313,0.198 10 false G19 2.188,1.875 2.646,2.073 0.458,0.198 10 false IG2
*a Front view of wire harness connector
(to Steering Lock Actuator or Upper Bracket Assembly)


a.

Disconnect the steering lock actuator or upper bracket assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G19-7 (B) - Body ground Always 11 to 14 V
G19-6 (IG2) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.REPLACE STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY
a.

Replace the steering lock actuator or upper bracket assembly with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Proceed to
DTC B2786 is not output
DTC B2786 is output



DTC B2786 is not output

END (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY IS DEFECTIVE)

DTC B2786 is output

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)