Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › TORQUE CONVERTER AND DRIVE PLATE
RM33K0E _52 Drivetrain _043590 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0211128 TORQUE CONVERTER AND DRIVE PLATE G

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  TORQUE CONVERTER AND DRIVE PLATE  INSPECTION  


PROCEDURE

Hide 32000 1.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

a.

Inspect the one-way clutch.

i.
C285724N01
1.448,0.823 0.75,0.604 0.75,0.604 1.385,0.656 true 0.427,0.51 0.781,0.698 0.354,0.188 10 false SST

Install SST into the inner race of the one-way clutch.

SST
09350-32014  (09351-32010)


ii.

Set SST so that it fits in the notch of the torque converter hub and the outer race of the one-way clutch.

SST
09350-32014  (09351-32020)


iii.
D029377C16
1.74,0.99 2.375,0.656 2.375,0.656 2.25,0.865 false 1.781,0.271 2.094,0.469 0.313,0.198 10 false *a 1.885,1.719 2.198,1.917 0.313,0.198 10 false *b 2.469,0.542 2.927,0.74 0.458,0.198 10 false SST
*a Hold
*b Turn
V100135

Lock
V100136

Free


With the torque converter assembly standing on its side, check that the clutch locks when SST is turned counterclockwise and rotates freely and smoothly when SST is turned clockwise.

If the results are not as specified, clean the torque converter assembly and recheck the one-way clutch.

If the results still are not as specified even after cleaning the torque converter assembly, replace the torque converter assembly.



b.
C197457C28
0.042,0.052 0.354,0.25 0.313,0.198 10 false *a
*a Sample showing maximum allowable amount of powder in ATF


Determine the condition of the torque converter assembly.

·

A metallic sound is emitted from the torque converter assembly during the stall test or when the shift lever is moved to N.

·

The one-way clutch turns smoothly or is locked in both directions.

·

The amount of powder in the ATF is more than the sample shown in the illustration (refer to the sample).


i.

Check that the following conditions are met:

·

During the stall test or when the shift lever is in N, metallic sounds are not emitted from the torque converter assembly.

·

The one-way clutch turns in one direction and locks in the other direction.

·

The amount of powder in the ATF is not more than the sample shown in the illustration.


If the results are not as specified, replace the torque converter assembly.

HINT:

The sample illustration shows approximately 0.025 liters (0.026 US. qts., 0.022 Imp. qts.) of ATF taken from a removed torque converter assembly.




c.

Replace the ATF in the torque converter assembly.

i.

If the ATF is discolored and/or has a foul odor, stir the ATF in the torque converter assembly thoroughly and drain the ATF with the torque converter assembly facing upward.



d.
D025368C26
1.729,1.865 2.146,1.448 false 0.5,0.135 0.813,0.333 0.313,0.198 10 false *a 1.542,0.146 1.854,0.344 0.313,0.198 10 false *b 2.208,1.302 2.521,1.5 0.313,0.198 10 false *c
*a CORRECT
*b INCORRECT
*c Bottom is damage


Prevent deformation of the torque converter and damage to the oil pump gear.

i.

When any marks due to interference are found on the end of a bolt for the torque converter assembly and on the bottom of the bolt hole, replace the bolt and torque converter assembly.


ii.

Make sure all of the bolts are the same length.


iii.

Make sure no spring washers are missing.



Hide 2.INSPECT DRIVE PLATE

a.

Check the drive plate for damage.


b.
C193846C09
0.073,1.729 0.333,1.896 0.26,0.167 0.073,1.76 0.115,1.729 false 0.073,1.802 0.156,1.729 false 0.073,1.844 0.198,1.729 false 0.083,1.885 0.25,1.729 false 0.125,1.885 0.292,1.729 false 0.167,1.885 0.333,1.729 false 0.219,1.885 0.333,1.771 false 0.26,1.885 0.333,1.813 false 0.302,1.885 0.333,1.854 false 0.396,1.729 0.604,1.927 0.208,0.198 10 false *a 1.313,0.969 1.49,1.167 0.177,0.198 10 false 1 1.688,0.292 1.854,0.479 0.167,0.188 10 false 2 2.479,0.406 2.698,0.604 0.219,0.198 10 false 3 2.958,1.146 3.135,1.323 0.177,0.177 10 false 4 2.771,1.833 2.938,2.042 0.167,0.208 10 false 5 1.875,1.854 2.042,2.052 0.167,0.198 10 false 6
*a Measurement Point


Set up a dial indicator and measure the runout at the 6 areas on the drive plate surface that contact the torque converter.

Maximum runout:

0.30 mm (0.0118 in.)


If the runout is more than the maximum, or the drive plate is damaged, replace the drive plate.

Click hereEngine / Hybrid System>1KD-FTV ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL