Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › SHIFT PADDLE SWITCH
RM33K0E _52 Drivetrain _043590 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0211183 SHIFT PADDLE SWITCH G

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT PADDLE SWITCH  INSPECTION  


PROCEDURE

Hide 84610F 1.INSPECT SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY)

a.
C327936C01
0.573,2.74 0.698,2.74 0.698,2.74 0.802,2.427 true 0.667,2.896 0.792,2.896 0.792,2.896 0.938,2.427 true 1.063,2.74 0.948,2.74 0.948,2.74 1.052,2.427 true 2.302,2.656 2.427,2.656 2.427,2.656 2.531,2.344 true 2.833,2.656 2.719,2.656 2.719,2.656 2.635,2.344 true 0.74,3.083 1.052,3.24 0.313,0.156 10 false *a 2.542,3.094 2.854,3.25 0.313,0.156 10 false *b 0.115,0.063 0.427,0.219 0.313,0.156 10 false *c 0.177,2.646 0.792,2.844 0.615,0.198 10 false ECC1 0.344,2.813 0.958,3.01 0.615,0.198 10 false ECC 1.125,2.646 1.74,2.844 0.615,0.198 10 false SDN 2.896,2.563 3.271,2.75 0.375,0.188 10 false ECC1 1.969,2.563 2.583,2.76 0.615,0.198 10 false SUP
*a Shift Paddle Switch LH (Transmission Shift Switch Assembly LH)
*b Shift Paddle Switch RH (Transmission Shift Switch Assembly RH)
*c Component without harness connected
(Shift Paddle Switch (Transmission Shift Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
LH
Tester Connection Shift Position Specified Condition
SDN - ECC "-" shift paddle operated and held (down-shift) Below 3 Ω
SDN - ECC1 "-" shift paddle operated and held (down-shift) Below 3 Ω
SDN - ECC "-" shift paddle not operated (down-shift) 1 MΩ or higher
SDN - ECC1 "-" shift paddle not operated (down-shift) 1 MΩ or higher

RH
Tester Connection Shift Position Specified Condition
SUP - ECC1 "+" shift paddle operated and held (up-shift) Below 3 Ω
SUP - ECC1 "+" shift paddle not operated (up-shift) 1 MΩ or higher


If the result is not as specified, replace the shift paddle switch (transmission shift switch assembly).


Hide 84523 2.INSPECT NO. 1 SWITCH WIRE

a.

Connect the No. 1 switch wire connector to the transmission shift switch assembly.


b.

Disconnect the steering pad switch assembly connector from the No. 1 switch wire.


c.
C279491C09
1.792,1.083 1.927,0.865 1.927,0.865 2.24,0.865 true 1.792,1.375 1.979,1.688 1.979,1.688 2.219,1.688 true 1.646,1.094 1.531,0.875 1.531,0.875 1.156,0.875 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.823,0.792 1.438,0.99 0.615,0.198 10 false SUP 2.302,0.781 2.917,0.979 0.615,0.198 10 false SDN 2.292,1.594 2.906,1.792 0.615,0.198 10 false ECC
*a Front view of wire harness connector
(to Steering Pad Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
SDN - ECC "-" shift paddle operated and held (down-shift) Below 3 Ω
SUP - ECC "+" shift paddle operated and held (up-shift) Below 3 Ω
SDN - ECC "-" shift paddle not operated (down-shift) 1 MΩ or higher
SUP - ECC "+" shift paddle not operated (up-shift) 1 MΩ or higher


If the result is not as specified, replace the No. 1 switch wire.