Home › Power Source / Network › 1GR-FE BATTERY / CHARGING › GENERATOR
RM33K0E _57 Power Source / Network _043598 1GR-FE BATTERY / CHARGING _0211296 GENERATOR A

1GR-FE BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 27310B 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A347002N01
2.375,0.927 2.156,0.25 2.156,0.25 2.51,0.573 true 1.917,0.073 2.375,0.271 0.458,0.198 10 false SST

Using SST and a press, press in a new generator drive end frame bearing.

SST
09950-60010  (09951-00470)
09950-70010  (09951-07100)


b.
A347003C01
2.542,2.01 2.625,2.01 2.625,2.01 2.896,1.281 true 2.083,0.438 2.167,0.438 2.167,0.438 2.813,0.813 true 1.906,0.344 2.219,0.5 0.313,0.156 10 false *a 2.365,1.896 2.677,2.052 0.313,0.156 10 false *b
*a Tab
*b Cutout


Fit the tabs on the retainer plate into the cutouts on the generator drive end frame.


c.

Install the retainer plate with the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Place the generator drive end frame on the generator pulley.


b.

Install the generator rotor assembly to the generator drive end frame.


Hide 27444 3.INSTALL GENERATOR BEARING COVER PACKING

NOTICE:

A new generator coil assembly comes with a generator bearing cover packing. Therefore, it is not necessary to install a new generator bearing cover packing when installing a new generator coil assembly.


a.
A314531C05
1.938,0.5 2.448,0.5 true 1.927,1.448 2.438,1.448 true 2.49,0.417 2.802,0.573 0.313,0.156 10 false *a 2.479,1.385 2.792,1.542 0.313,0.156 10 false *b
*a Protrusions
*b Grooves


Install a new generator bearing cover packing to the generator coil assembly.

NOTICE:

Align the protrusions of the generator bearing cover packing with the grooves of the generator coil assembly when installing.



Hide 27360 4.INSTALL GENERATOR COIL ASSEMBLY

a.
A347004C01
0.656,0.198 0.75,0.198 0.75,0.198 1.292,0.635 true 1.979,0.177 2.073,0.177 2.073,0.177 2.615,0.615 true 0.469,0.115 0.781,0.271 0.313,0.156 10 false *a 1.771,0.073 2.083,0.229 0.313,0.156 10 false *a
*a 21 mm Deep Socket Wrench


Using a 21 mm deep socket wrench and press, slowly press in the generator coil assembly.


b.

Install the generator coil assembly with the 4 bolts.

Torque:
5.6 N*m (57 kgf*cm, 50 in.*lbf)


Hide 27370 5.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A153827C14
2.469,0.813 1.958,0.198 1.958,0.198 1.708,0.198 true 0.896,0.531 0.583,0.188 0.583,0.188 0.333,0.188 false 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 1.49,0.115 1.802,0.271 0.313,0.156 10 false *a
*a Pin


While pushing the 2 brushes into the generator brush holder assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.


b.
A346995C01
0.927,1.875 1,1.875 1,1.875 1.708,1.021 true 0.729,1.792 1.042,1.948 0.313,0.156 10 false *a
*a Pin


Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the generator brush holder assembly.


Hide 27387B 6.INSTALL GENERATOR TERMINAL INSULATOR

a.
A347006

Install the terminal insulator to the generator coil assembly.

NOTICE:

Make sure that the generator terminal insulator is installed with the correct orientation.



Hide 27039 7.INSTALL GENERATOR REAR END COVER

a.

Install the generator rear end cover to the generator coil assembly with the 3 bolts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 27415 8.INSTALL GENERATOR PULLEY

a.

Temporarily install the generator pulley by hand.


b.

Mount the generator assembly in the vise between aluminum plates.


c.
A323643C05
2.844,1.448 2.844,1.167 2.844,1.167 3.135,0.719 true 2.167,0.198 2.375,0.198 2.375,0.198 2.938,0.521 true 1.698,1.917 2.01,2.115 0.313,0.198 10 true *a 1.573,0.125 2.646,0.323 1.073,0.198 10 false SST 1-B 2.583,1.479 3.323,1.688 0.74,0.208 10 false SST 1-A
*a Hold
V100135

Turn


Install SST 1-A and B to the generator pulley shaft.

SST
09820-63011  (09820-06010, 09820-06021)

SST 1-A and B 09820-06010
SST 2 09820-06021


d.

Install SST 1-B to SST 1-A.


e.

Hold SST 1-A with a torque wrench and turn SST 1-B clockwise with the specified torque.

NOTICE:

Make sure that SST is secured to the generator rotor shaft.



f.
A346990C01
2.583,0.75 2.75,0.417 2.75,0.417 2.833,0.417 false 2,0.781 2.25,0.198 2.25,0.198 2.333,0.198 false 2.906,0.333 3.406,0.583 0.5,0.25 10 false SST 2 2.385,0.115 3.167,0.333 0.781,0.219 10 false SST 1-A
V100135

Insert


Insert SST 2 and attach it to the pulley nut.


g.
A347008C01
1.573,1.625 1.885,1.781 0.313,0.156 10 false *a
*a Hold
V100135

Turn


Tighten the pulley nut by turning SST 1-A as shown in the illustration.

Torque:
132.5 N*m (1351 kgf*cm, 98 ft.*lbf)


h.

Remove SST 2 from the generator assembly.


i.
A323644C06
2.167,0.135 2.396,0.135 2.396,0.135 2.917,0.448 true 2.833,1.292 2.833,1.021 2.833,1.021 3.083,0.667 true 2.229,1.719 2.542,1.917 0.313,0.198 10 true *a 1.594,0.052 2.396,0.26 0.802,0.208 10 false SST 1-B 2.573,1.323 3.292,1.51 0.719,0.188 10 false SST 1-A
*a Hold
V100135

Turn


Turn SST 1-B as shown in the illustration and remove SST 1-A and B.


j.

Turn the generator pulley and check that the generator pulley moves smoothly.


k.

Remove the generator assembly from the vise.