1.INSTALL STRAIGHT PIN AND RING PIN
It is not necessary to remove a straight pin and ring pin unless it is being replaced.
| *a | Protrusion Height |
Using a plastic-faced hammer, tap 4 new ring pins into the intermediate plate.
| Item | Specified Condition |
|---|---|
| A | 5.5 to 7.5 mm (0.217 to 0.295 in.) |
| *a | Protrusion Height |
Using a plastic-faced hammer, tap 2 new straight pins into the transmission case.
| Item | Specified Condition |
|---|---|
| A | 9.0 to 11.0 mm (0.355 to 0.433 in.) |
2.INSTALL OUTPUT SHAFT
Apply gear oil to the sliding part of the output shaft.
Using a plastic-faced hammer, install the output shaft by tapping the intermediate plate.
33321B
3.INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING
Using a snap ring expander, install a new output shaft bearing shaft snap ring to the output shaft.
33368
4.INSPECT NO. 2 SYNCHRONIZER RING
5.INSTALL INPUT SHAFT
Apply gear oil to the input shaft and No. 2 synchronizer ring, and install them to the output shaft.
When installing the input shaft to the output shaft, align the protrusion of the No. 2 synchronizer ring with the cutout of the transmission clutch hub.
Check that the input shaft rotates slightly.
33421
6.INSTALL COUNTER GEAR
Temporarily install the counter gear to the intermediate plate.
33411P
7.INSTALL COUNTER SHAFT REAR BEARING
Using SST and a hammer, tap in a new counter shaft rear bearing to the intermediate plate.
Install the counter shaft rear bearing while tapping the tip of the counter gear with a plastic-faced hammer so that the counter gear does not hit the side wall of the output shaft gear by being pushed forward.
Using a snap ring expander, install the snap ring.
33402
8.INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY
Apply gear oil to each sliding part of the reverse idler gear sub-assembly and the reverse idler gear shaft, and install the reverse idler gear sub-assembly and reverse idler shaft to the intermediate plate.
Install the reverse idler shaft with its groove facing the rear side, and install it from the rear side.
33151
9.INSTALL OUTPUT SHAFT REAR BEARING RETAINER
Insert the output shaft rear bearing retainer into the groove of the reverse idler gear shaft and install it with the 4 bolts.
33349C
10.INSTALL 5TH GEAR THRUST WASHER PIN
Apply MP grease to the 5th gear thrust washer pin, and install it to the counter gear.
33349
11.INSTALL 5TH GEAR THRUST WASHER
Apply gear oil to the 5th gear thrust washer, and install it to the counter gear.
Install the 5th gear thrust washer so that its chamfer side faces forward.
33394B
12.INSTALL NO. 3 SYNCHROMESH SHIFTING KEY
Apply gear oil to the sliding part of the No. 3 transmission hub sleeve, and install the hub sleeve to the counter 5th gear.
Make sure that the No. 3 transmission hub sleeve and counter 5th gear are installed facing the correct direction.
| *a | Cutout |
| *b | Protrusion |
Install the 2 No. 3 synchromesh shifting keys and No. 3 synchromesh shifting key spring to the counter 5th gear as shown in the illustration.
When installing the No. 3 synchromesh shifting key spring, make sure the protrusion fits into the cutout.
Using a snap ring expander, install a new shaft snap ring to the counter 5th gear.
33428B
13.INSTALL COUNTER 5TH GEAR BEARING
Apply gear oil to the counter 5th gear bearing and install it to the countershaft 5th gear.
33428
14.INSTALL COUNTERSHAFT 5TH GEAR
Apply gear oil to the countershaft 5th gear and No. 3 transmission hub sleeve, and install them to the countershaft.
33384A
15.INSTALL NO. 3 SYNCHRONIZER RING
Apply gear oil to the No. 3 synchronizer ring, and install it to the countershaft 5th gear.
Install the No. 3 synchronizer ring so that its protrusion fits between the 2 synchromesh shifting keys.
33318
16.INSTALL NO. 5 GEAR SPLINE PIECE
Using SST and a press, press in the No. 5 gear spline piece to the countershaft 5th gear.
Check that the gear rotates freely.
33421R
17.INSTALL COUNTER SHAFT REAR SNAP RING
| *a | Thrust Clearance |
Select a new snap ring so that the thrust clearance between the No. 5 gear spline piece and snap ring is within the specification.
0.10 mm (0.00393 in.) or less
| Thickness |
|---|
| 2.80 to 2.85 mm (0.111 to 0.112 in.) |
| 2.85 to 2.90 mm (0.113 to 0.114 in.) |
| 2.90 to 2.95 mm (0.115 to 0.116 in.) |
| 2.95 to 3.00 mm (0.117 to 0.118 in.) |
| 3.00 to 3.05 mm (0.119 to 0.120 in.) |
| 3.05 to 3.10 mm (0.121 to 0.122 in.) |
| 3.10 to 3.15 mm (0.123 to 0.124 in.) |
Using a brass bar and hammer, install the snap ring.
33428
18.INSPECT COUNTERSHAFT 5TH GEAR THRUST CLEARANCE
33428
19.INSPECT COUNTERSHAFT 5TH GEAR RADIAL CLEARANCE
33321A
20.INSTALL OUTPUT SHAFT REAR BEARING
Using SST and a press, press in the spacer and a new output shaft rear bearing to the output shaft.
Select a new shaft snap ring so that the thrust clearance between the output shaft rear bearing and shaft snap ring is within the specification.
0.10 mm (0.00393 in.) or less
| Thickness | Thickness |
|---|---|
| 2.65 to 2.70 mm (0.105 to 0.106 in.) | 3.10 to 3.15 mm (0.122 to 0.124 in.) |
| 2.70 to 2.75 mm (0.107 to 0.108 in.) | 3.15 to 3.20 mm (0.124 to 0.126 in.) |
| 2.75 to 2.80 mm (0.109 to 0.110 in.) | 3.20 to 3.25 mm (0.126 to 0.128 in.) |
| 2.80 to 2.85 mm (0.111 to 0.112 in.) | 3.25 to 3.30 mm (0.128 to 0.129 in.) |
| 2.85 to 2.90 mm (0.113 to 0.114 in.) | 3.30 to 3.35 mm (0.130 to 0.131 in.) |
| 2.90 to 2.95 mm (0.115 to 0.116 in.) | 3.35 to 3.40 mm (0.132 to 0.133 in.) |
| 2.95 to 3.00 mm (0.117 to 0.118 in.) | 3.40 to 3.45 mm (0.134 to 0.135 in.) |
| 3.00 to 3.05 mm (0.119 to 0.120 in.) | 3.45 to 3.50 mm (0.136 to 0.137 in.) |
| 3.05 to 3.10 mm (0.121 to 0.122 in.) | - |
Using a brass bar and hammer, install the output shaft bearing shaft snap ring.
33481
21.INSTALL SPEEDOMETER DRIVE GEAR
Using snap ring pliers, install a new snap ring.
Install the steel ball and speedmeter drive gear.
Using snap ring pliers, install a new snap ring.
33228
22.INSTALL REVERSE SHIFT ARM BRACKET
Install the reverse shift arm to the reverse shift arm bracket with a new snap ring.
| *1 | Reverse Idler Gear |
| *2 | Reverse Shift Arm |
Insert the tip of the reverse shift arm into the reverse idler gear sub-assembly.
Install the reverse shift arm bracket with the 2 bolts.
Install the torsion spring to the reverse shift arm bracket.
Make sure that the torsion spring is securely installed to the reverse shift arm.
33211
23.INSTALL REVERSE SHIFT FORK
Install the reverse shift fork to the reverse shift arm.
33241
24.INSTALL NO. 3 GEAR SHIFT FORK SHAFT
Install the No. 3 gear shift fork to the No. 3 transmission hub sleeve and No. 3 gear shift fork shaft to the intermediate plate from the front side.
Install the No. 1 shift interlock roller to the reverse shift fork.
Using a brass bar and hammer, install a new shift fork shaft snap ring to the No. 3 gear shift fork shaft.
Using a 5 mm pin punch and hammer, install a new shift fork set slotted spring pin to the No. 3 gear shift fork.
33242
25.INSTALL NO. 1 GEAR SHIFT FORK SHAFT
Install the No. 1 shift interlock roller to the intermediate plate.
Install the No. 1 gear shift fork to the reverse gear.
Install the No. 1 gear shift fork shaft to the intermediate plate from the rear side.
Install a new bolt to the No. 1 gear shift fork shaft.
Using a brass bar and hammer, install a new shift fork shaft snap ring to the No. 1 gear shift fork shaft.
33243A
26.INSTALL NO. 2 GEAR SHIFT FORK SHAFT
| *1 | No. 1 Shift Interlock Roller |
| *2 | Shift Interlock Pin |
Install the shift interlock pin and No. 1 shift interlock roller to the intermediate plate.
Install the No. 2 gear shift fork to the No. 2 transmission hub sleeve.
Apply gear oil to the No. 2 gear shift fork shaft, and install the No. 2 gear shift fork shaft to the intermediate plate from the rear side.
Install a new bolt to the No. 2 gear shift fork.
Using a brass bar and hammer, install a new shift fork shaft snap ring to the No. 2 gear shift fork shaft.
27.INSTALL SHIFT DETENT BALL PLUG
Install 2 new shift detent ball compression springs and 2 shift detent balls to the intermediate plate.
| *a | for Type A |
| *b | for Type B |
Install 2 new shift detent ball plugs to the intermediate plate.
for Type A:
Using a T40 ''TORX'' socket wrench, install 2 new shift detent ball plugs to the intermediate plate.
for Type B
Using a 6 mm hexagon socket wrench, install 2 new shift detent ball plugs to the intermediate plate.
Install the shift detent ball and shift detent ball compression spring to the intermediate plate.
| *a | for Type A |
| *b | for Type B |
Install new shift detent ball plug to the intermediate plate.
for Type A:
Using a T40 ''TORX'' socket wrench, install a new shift detent ball plug to the intermediate plate.
for Type B
Using a 6 mm hexagon socket wrench, install a new shift detent ball plug to the intermediate plate.
33449B
28.INSTALL TRANSMISSION MAGNET
Clean the transmission magnet, and install it to the intermediate plate.
33111
29.INSTALL MANUAL TRANSMISSION CASE
| *a | Seal Packing |
Apply seal packing to the manual transmission case as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
Using a plastic-faced hammer, tap the manual transmission case to attach it to the intermediate plate.
33411Q
30.INSTALL COUNTER GEAR FRONT BEARING SNAP RING
Using a snap ring expander, install the counter gear front bearing snap ring to the manual transmission case.
33311G
31.INSTALL FRONT BEARING SHAFT SNAP RING
Using a snap ring expander, install the front bearing shaft snap ring to the manual transmission case.
33131A
32.INSTALL TRANSMISSION FRONT BEARING RETAINER OIL SEAL
33131
33.INSTALL FRONT BEARING RETAINER
Clean and degrease the contact surface of the front bearing retainer and manual transmission case.
Clean and degrease the 8 bolts and the installation holes in the manual transmission case.
| *a | Seal Packing |
Apply seal packing to the front bearing retainer as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.
Apply seal packing in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface of the manual transmission case
Install the front bearing retainer to the manual transmission case with 8 new bolts.
Check that the input shaft and output shaft rotate smoothly.
33103R
34.INSTALL MANUAL TRANSMISSION EXTENSION HOUSING OIL SEAL
Using SST and a hammer, tap in a new manual transmission extension housing oil seal to the extension housing sub-assembly.
-0.5 to 0.5 mm (-0.196 to 0.196 in.)
Be careful not to damage the oil seal lip.
Lightly apply MP grease to the lip of the manual transmission extension housing oil seal.
33280
35.INSTALL REVERSE RESTRICT PIN
Install the reverse restrict pin to the extension housing sub-assembly.
Using a 5 mm pin punch and hammer, tap in the slotted pin to the extension housing sub-assembly.
Using a T40 ''TORX'' socket wrench, install a new plug to the transfer adapter sub-assembly.
33124F
36.INSTALL NO. 1 EXTENSION HOUSING OIL RECEIVER PIPE
Install the No. 1 extension housing oil receiver pipe with the bolt.
33124G
37.INSTALL NO. 2 EXTENSION HOUSING OIL RECEIVER PIPE
Install the No. 2 extension housing oil receiver pipe to the extension housing sub-assembly.
33146
38.INSTALL EXTENSION HOUSING DUST DEFLECTOR
Using SST and a hammer, tap in the extension housing dust deflector.
33103
39.INSTALL EXTENSION HOUSING SUB-ASSEMBLY
| *a | Seal Packing |
Apply seal packing to the extension housing sub-assembly as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
Install the shift and select lever to the extension housing sub-assembly.
Connect the shift and select lever to the fork shaft and install the shift lever housing.
Align the shift and select lever with the extension housing sub-assembly installation hole and push into the extension housing sub-assembly.
Install the extension housing sub-assembly to the manual transmission case with the 10 bolts.
Install a new bolt to the shift lever housing.
33506F
40.INSTALL FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY
Install a new gasket and the floor shift control shift lever retainer sub-assembly.
Install the 6 bolts.
33280
41.INSTALL REVERSE RESTRICT PIN ASSEMBLY
| *a | White |
| *b | Green |
Install the 2 reverse restrict pin assemblies.
84210
42.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY
31111
43.INSTALL CLUTCH HOUSING
Clean the threads of the bolts and the manual transmission case with non-residue solvent.
| *a | Precoated Bolt |
Install the clutch housing to the manual transmission case with the 7 bolts.
Install 2 new bolts (labeled A).
31236B
44.INSTALL RELEASE FORK SUPPORT
31230
45.INSTALL CLUTCH RELEASE BEARING ASSEMBLY
31126
46.INSTALL CLUTCH RELEASE FORK BOOT
33104
47.INSTALL DRAIN PLUG SUB-ASSEMBLY
Install a new gasket and the drain plug sub-assembly to the manual transmission case.
33101A
48.INSTALL MANUAL TRANSMISSION FILLER PLUG
Install a new gasket and the manual transmission filler plug to the manual transmission case.