33101A
1.REMOVE MANUAL TRANSMISSION FILLER PLUG
Remove the manual transmission filler plug and gasket from the manual transmission case.
33104
2.REMOVE DRAIN PLUG SUB-ASSEMBLY
Remove the drain plug sub-assembly and gasket from the manual transmission case.
31126
3.REMOVE CLUTCH RELEASE FORK BOOT
31230
4.REMOVE CLUTCH RELEASE BEARING ASSEMBLY
31236B
5.REMOVE RELEASE FORK SUPPORT
31111
6.REMOVE CLUTCH HOUSING
Remove the 9 bolts.
Using a plastic-faced hammer, tap off the clutch housing from the manual transmission case.
84210
7.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY
33280
8.REMOVE REVERSE RESTRICT PIN ASSEMBLY
Remove the 2 reverse restrict pin assemblies from the transfer adapter sub-assembly.
33506F
9.REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY
Remove the 4 bolts.
Remove the floor shift control shift lever retainer sub-assembly.
Remove the control shift lever retainer gasket.
36107A
10.REMOVE TRANSFER ADAPTER SUB-ASSEMBLY
Remove the 10 bolts and 2 wire harness brackets.
Using a brass bar and a hammer, tap out the transfer adapter sub-assembly from the manual transmission case.
33251
11.REMOVE SHIFT AND SELECT LEVER
Remove the bolt from the shift lever housing.
Remove the shift and select lever and shift lever housing from the transfer adapter sub-assembly.
33124E
12.REMOVE TRANSFER OIL RECEIVER PIPE
Remove the transfer oil receiver pipe from the transfer adapter sub-assembly.
33283F
13.REMOVE REVERSE RESTRICT PIN
Using a T40 ''TORX'' socket wrench, remove the plug.
Using a 5 mm pin punch and hammer, tap out the reverse restrict slotted pin.
Remove the reverse restrict pin.
36117A
14.REMOVE TRANSFER ADAPTER OIL SEAL
33131
15.REMOVE FRONT BEARING RETAINER
Remove the 8 bolts.
Using a brass bar and hammer, tap off the front bearing retainer from the manual transmission case.
33131A
16.REMOVE TRANSMISSION FRONT BEARING RETAINER OIL SEAL
33311G
17.REMOVE FRONT BEARING SHAFT SNAP RING
Using a snap ring expander, remove the front bearing shaft snap ring from the manual transmission case.
33411Q
18.REMOVE COUNTER GEAR FRONT BEARING SNAP RING
Using a snap ring expander, remove the counter gear front bearing snap ring from the manual transmission case.
33111
19.REMOVE MANUAL TRANSMISSION CASE
Using a brass bar and hammer, tap off the manual transmission case from the intermediate plate.
33449B
20.REMOVE TRANSMISSION MAGNET
Remove the transmission magnet from the intermediate plate.
21.SECURE INTERMEDIATE PLATE
Secure the intermediate plate in a vise between aluminum plates.
22.REMOVE SHIFT DETENT BALL PLUG
| *a | for Type A |
| *b | for Type B |
Remove the shift detent ball plug from the intermediate plate.
for Type A:
Using a T40 ''TORX'' socket wrench, remove the shift detent ball plug from the intermediate plate.
for Type B:
Using a 6 mm hexagon socket wrench, remove the shift detent ball plug from the intermediate plate.
Using a magnet hand, remove the shift detent ball compression spring and shift detent ball from the intermediate plate.
| *a | for Type A |
| *b | for Type B |
Remove the shift detent ball plug from the intermediate plate.
for Type A:
Using a T40 ''TORX'' socket wrench, remove the 2 shift detent ball plugs from the intermediate plate.
for Type B:
Using a 6 mm hexagon socket wrench, remove the 2 shift detent ball plugs from the intermediate plate.
Using a magnet hand, remove the 2 shift detent ball compression springs and 2 shift detent balls from the intermediate plate.
33243A
23.REMOVE NO. 2 GEAR SHIFT FORK SHAFT
Using 2 screwdrivers and a hammer, tap off the shift fork shaft snap ring from the No. 2 gear shift fork shaft.
Use a cloth to prevent the shift fork shaft snap ring from flying off.
Remove the bolt from the No. 2 gear shift fork.
Remove the No. 2 gear shift fork shaft from the intermediate plate.
Remove the No. 2 gear shift fork from the No. 2 transmission hub sleeve.
Using a magnet hand, remove the No. 1 shift interlock roller and shift interlock pin from the intermediate plate.
33242
24.REMOVE NO. 1 GEAR SHIFT FORK SHAFT
Using 2 screwdrivers and a hammer, tap off the shift fork shaft snap ring from the No. 1 gear shift fork shaft.
Use a cloth to prevent the shift fork shaft snap ring from flying off.
Remove the bolt from the No. 1 gear shift fork.
Remove the No. 1 gear shift fork shaft from the intermediate plate.
Remove the No. 1 gear shift fork from the reverse gear.
Using a magnet hand, remove the No. 1 shift interlock roller from the intermediate plate.
33241
25.REMOVE NO. 3 GEAR SHIFT FORK SHAFT
Using a 5 mm pin punch and hammer, tap out the shift fork set slotted spring pin from the No. 3 gear shift fork shaft.
Using 2 screwdrivers and a hammer, tap off the shift fork shaft snap ring from the No. 3 gear shift fork shaft.
Use a cloth to prevent the shift fork shaft snap ring from flying off.
Using a magnet hand, remove the No. 1 shift interlock roller from the reverse shift fork.
Remove the No. 3 gear shift fork and No. 3 gear shift fork shaft from the intermediate plate.
33211
26.REMOVE REVERSE SHIFT FORK
Remove the reverse shift fork from the reverse shift arm.
33228
27.REMOVE REVERSE SHIFT ARM BRACKET
Remove the torsion spring from the reverse shift arm bracket.
Remove the 2 bolts and reverse shift arm bracket from the intermediate plate.
Using a screwdriver, remove the snap ring from the reverse shift arm bracket.
Remove the reverse shift arm from the reverse shift arm bracket.
33321A
28.REMOVE OUTPUT SHAFT REAR BEARING
Using 2 screwdrivers and a hammer, tap off the shaft snap ring from the output shaft.
| *a | Hold |
| *b | Turn |
Using SST, remove the output shaft rear bearing and output shaft spacer from the output shaft.
29.INSPECT COUNTERSHAFT 5TH GEAR THRUST CLEARANCE
30.INSPECT COUNTERSHAFT 5TH GEAR RADIAL CLEARANCE
33421R
31.REMOVE COUNTER SHAFT REAR SNAP RING
Using 2 screwdrivers and a hammer, tap off the counter shaft rear snap ring from the countershaft 5th gear.
33395
32.REMOVE NO. 3 TRANSMISSION HUB SLEEVE
Remove the No. 3 transmission hub sleeve from the countershaft 5th gear.
33428
33.REMOVE COUNTERSHAFT 5TH GEAR
Using SST, remove the countershaft 5th gear together with the 2 No. 3 synchromesh shifting keys, No. 3 synchromesh shifting key spring, No. 3 synchronizer ring and No. 5 gear spline piece from the counter gear.
33318
34.REMOVE NO. 5 GEAR SPLINE PIECE
| *1 | No. 5 Gear Spline Piece |
| *2 | No. 3 Synchronizer Ring |
| *3 | Countershaft 5th Gear |
Remove the No. 5 gear spline piece from the countershaft 5th gear.
33384A
35.REMOVE NO. 3 SYNCHRONIZER RING
Remove the No. 3 synchronizer ring from the countershaft 5th gear.
33428B
36.REMOVE COUNTER 5TH GEAR BEARING
Remove the counter 5th gear bearing from the countershaft 5th gear.
33394B
37.REMOVE NO. 3 SYNCHROMESH SHIFTING KEY
Using a snap ring expander, remove the shaft snap ring.
| *1 | No. 3 Synchromesh Shifting Key Spring |
| *2 | No. 3 Synchromesh Shifting Key |
| *3 | Countershaft 5th Gear |
Remove the No. 3 synchromesh shifting key spring and 2 No. 3 synchromesh shifting keys from the countershaft 5th gear.
33349
38.REMOVE 5TH GEAR THRUST WASHER
Remove the 5th gear thrust washer from the counter gear.
33349C
39.REMOVE 5TH GEAR THRUST WASHER PIN
Remove the 5th gear thrust washer pin from the counter gear.
33151
40.REMOVE OUTPUT SHAFT REAR BEARING RETAINER
Remove the 4 bolts and output shaft rear bearing retainer from the intermediate plate.
33402
41.REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY
Pull out the reverse idler gear shaft and reverse idler gear sub-assembly from the intermediate plate.
33411P
42.REMOVE COUNTER SHAFT REAR BEARING
Using a snap ring expander, remove the snap ring.
Using SST, remove the counter shaft rear bearing from the intermediate plate.
Remove the counter shaft rear bearing while tapping the tip of the counter gear so that the counter gear does not hit the side wall of the output shaft gear by being pushed forward.
33421
43.REMOVE COUNTER GEAR
Remove the counter gear from the intermediate plate.
33311
44.REMOVE INPUT SHAFT
Remove the input shaft and No. 2 synchronizer ring from the output shaft.
Do not drop the input shaft bearing and No. 2 synchronizer ring.
33368
45.INSPECT NO. 2 SYNCHRONIZER RING
33321B
46.REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING
Using a snap ring expander, remove the output shaft bearing shaft snap ring from the output shaft.
33321
47.REMOVE OUTPUT SHAFT
Using a plastic-faced hammer, remove the output shaft by tapping the intermediate plate.
48.REMOVE STRAIGHT PIN
If a straight pin is deformed or its threads are damaged, replace it.
49.REMOVE RING PIN
If a ring pin is deformed or its threads are damaged, replace it.
33384A
50.INSPECT NO. 3 SYNCHRONIZER RING
33395
51.INSPECT NO. 3 TRANSMISSION HUB SLEEVE
33428
52.INSPECT COUNTERSHAFT 5TH GEAR
33402
53.INSPECT REVERSE IDLER GEAR SUB-ASSEMBLY