Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)
RM33K0E _56 Audio / Visual / Telematics _043541 AUDIO / VIDEO _0218827 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when the switch is continuously depressed occurs.

Therefore, the radio receiver assembly cannot be operated using the steering pad switch assembly, and the radio receiver assembly itself cannot function.

WIRING DIAGRAM

E316668E05
6.042,2.823 7.094,3.208 1.052,0.385 10 false G108 6.042,2.979 7.094,3.365 1.052,0.385 10 false Radio Receiver Assembly 6.135,2.323 6.917,2.708 0.781,0.385 10 false SW2 6.135,0.604 6.917,0.99 0.781,0.385 10 false SW1 6.125,1.479 6.906,1.865 0.781,0.385 10 false SWG 4.833,1.375 5.615,1.76 0.781,0.385 10 false EAU 4.833,0.542 5.615,0.927 0.781,0.385 10 false AU1 4.865,2.26 5.646,2.646 0.781,0.385 10 false AU2 5.406,2.375 6.188,2.76 0.781,0.385 10 false G4 5.406,1.51 6.188,1.896 0.781,0.385 10 false G4 5.417,0.635 6.198,1.021 0.781,0.385 10 false G4 5.458,0.438 6.24,0.823 0.781,0.385 10 false 6 5.448,1.302 6.229,1.688 0.781,0.385 10 false 3 5.458,2.177 6.24,2.563 0.781,0.385 10 false 5 4.229,2.833 5.781,3.167 1.552,0.333 10 false Spiral with Sensor Cable Sub-assembly 1.573,2.865 3.74,3.271 2.167,0.406 10 false Steering Pad Switch Assembly 4.417,2.365 5.198,2.75 0.781,0.385 10 false z2 4.406,1.5 5.188,1.885 0.781,0.385 10 false z2 4.406,0.635 5.188,1.021 0.781,0.385 10 false z2 4.396,0.438 5.177,0.823 0.781,0.385 10 false 11 4.448,1.313 5.229,1.698 0.781,0.385 10 false 8 4.406,2.177 5.188,2.563 0.781,0.385 10 false 10 5.865,0.531 6.646,0.917 0.781,0.385 10 false 21 5.865,1.385 6.646,1.771 0.781,0.385 10 false 23 5.854,2.26 6.635,2.646 0.781,0.385 10 false 22 3.26,1.042 4.042,1.427 0.781,0.385 10 false Mode 2.458,1.031 3.24,1.417 0.781,0.385 10 false On Hook 1.729,1.031 2.51,1.417 0.781,0.385 10 false Off Hook 1,1.927 1.781,2.313 0.781,0.385 10 false Volume- 1.75,1.927 2.531,2.313 0.781,0.385 10 false Volume+ 2.5,1.927 3.281,2.313 0.781,0.385 10 false Seek- 3.229,1.917 4.01,2.302 0.781,0.385 10 false Seek+

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

for Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY
a.

Remove the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY)
a.

Disconnect the G108 radio receiver assembly connector.


b.

Disconnect the G4 spiral with sensor cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G108-21 (SW1) - G4-6 (AU1) Always Below 1 Ω
G108-22 (SW2) - G4-5 (AU2) Always Below 1 Ω
G108-23 (SWG) - G4-3 (EAU) Always Below 1 Ω
G108-21 (SW1) or G4-6 (AU1) - Body ground Always 10 kΩ or higher
G108-22 (SW2) or G4-5 (AU2) - Body ground Always 10 kΩ or higher
G108-23 (SWG) or G4-3 (EAU) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR