Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CENTER AIRBAG SENSOR ASSEMBLY
RM33K0E _58 Vehicle Interior _043552 SUPPLEMENTAL RESTRAINT SYSTEMS _0219480 CENTER AIRBAG SENSOR ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CENTER AIRBAG SENSOR ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the airbag sensor assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal w/ Power Back Door System:
Reset back door close position
Power back door system (Click here)

PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

for Type A:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

for Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 55395C 4.REMOVE INNER NO. 1 INSTRUMENT PANEL BRACKET COVER LH (for LHD)

a.
B430744C01
0,0 0,0 false
V113147

Fold Back in this Direction


Remove the 2 clips and fold back both sides of the floor carpet.


b.
B430745

Remove the 3 clips.


c.

Detach the guide and remove the inner No. 1 instrument panel bracket cover LH.


Hide 89170 5.REMOVE AIRBAG SENSOR ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·
B392779

If this procedure is performed without disconnecting the negative (-) terminal of the battery, the airbag may deploy even if an impact is applied only to the airbag sensor assembly. Therefore, make sure that the negative (-) terminal of the battery is disconnected before performing this procedure.




c.
B404134C01
0,0 0,0 false
V113147

Fold Back in this Direction


for RHD:

Remove the 2 clips and fold back both sides of the floor carpet.


d.
B430746C01
2.115,2.177 2.406,2.875 true 1.01,0.833 1.479,1.146 true 1.51,1.063 1.719,1.25 0.208,0.188 10 true *a 2.333,2.927 2.552,3.115 0.219,0.188 10 true *b
*a Connector Lock Lever
*b Waterproof Sheet
V113147

Push in this Direction
V113148

Release in this Direction


Disconnect the airbag connector.

NOTICE:
·

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

·

Do not remove the waterproof sheet.



i.

Push and pull the connector lock lever to release the connector lock as shown in the illustration.


ii.

Disconnect the airbag connector.



e.
B430755

Remove the 3 bolts and airbag sensor assembly.

NOTICE:

If the airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the airbag sensor assembly with a new one.