Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2015.11–2016.07
RM33K0E _56 Audio / Visual / Telematics _043542 NAVIGATION / MULTI INFO DISPLAY _0219471 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Illumination Circuit  


DESCRIPTION

Power is supplied to the navigation receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E341253E02
0.969,0.354 3.26,0.552 2.292,0.198 10 false from TAIL Relay 3.969,1.448 4.188,1.625 0.219,0.177 10 false z2 3.969,3.042 4.188,3.219 0.219,0.177 10 false z2 4,1.24 4.219,1.417 0.219,0.177 10 false 5 3.979,2.854 4.198,3.031 0.219,0.177 10 false 8 4.427,1.323 4.781,1.51 0.354,0.188 10 false IL+2 4.417,2.927 4.771,3.115 0.354,0.188 10 false EAU 5,1.448 5.354,1.635 0.354,0.188 10 false G4 5.01,1.25 5.365,1.438 0.354,0.188 10 false 13 5.01,3.052 5.365,3.24 0.354,0.188 10 false G4 5.063,2.854 5.417,3.042 0.354,0.188 10 false 3 5.667,1.458 6.021,1.646 0.354,0.188 10 false G43 5.667,3.052 6.021,3.24 0.354,0.188 10 false G41 5.667,5.948 6.021,6.135 0.354,0.188 10 false G44 5.708,1.26 6.063,1.448 0.354,0.188 10 false 10 5.729,2.854 6.083,3.042 0.354,0.188 10 false 23 5.76,5.75 6.115,5.938 0.354,0.188 10 false 5 3.885,3.708 5.438,4.083 1.552,0.375 10 false Spiral with Sensor Cable Sub-assembly*1 3.438,6.49 5.344,6.729 1.906,0.24 10 false Combination Meter Assembly 3.844,4.448 5.677,4.667 1.833,0.219 10 false Spiral Cable Sub-assembly*2 5.792,6.698 7.052,7.052 1.26,0.354 10 false Navigation Receiver Assembly 4.49,5.938 4.844,6.146 0.354,0.208 10 false ILL- 4.833,5.844 5.188,6.052 0.354,0.208 10 false 21 6.042,5.948 6.396,6.135 0.354,0.188 10 false ILL- 6.042,3.052 6.49,3.24 0.448,0.188 10 false SWG 6.031,1.448 6.385,1.635 0.354,0.188 10 false ILL+ 0.635,3.354 2.927,3.552 2.292,0.198 10 false Steering Pad Switch LH Side 0.677,5.552 2.969,5.75 2.292,0.198 10 false Steering Pad Switch RH Side 0.719,6.125 3.01,6.323 2.292,0.198 10 false Steering Pad Switch Assembly 0.281,6.969 2.573,7.167 2.292,0.198 10 false *1: w/ VSC 0.271,7.26 2.563,7.458 2.292,0.198 10 false *2: w/o VSC 3.438,6.344 5.344,6.583 1.906,0.24 10 false G9

CAUTION / NOTICE / HINT

CAUTION:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System.


NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the panel switch of the navigation receiver assembly dims, the screen changes to the night screen, or illumination for the steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination other than that for the steering pad switch assembly properly functions. A
Illumination other than that for the navigation receiver assembly properly functions. B
Illumination does not function at all (navigation receiver assembly, hazard switch, heater control switch, etc.). C




A

2.CHECK VEHICLE CONDITION

B

9.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

2.CHECK VEHICLE CONDITION
a.

Check the vehicle condition.


Result:
Result Proceed to
w/ VSC A
w/o VSC B



A

3.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY AND BATTERY)

B

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY AND BATTERY)
3.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY AND BATTERY)
a.

Disconnect the G41 navigation receiver assembly connector.


b.

Disconnect the G4 spiral with sensor cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G41-23 (SWG) - G4-3 (EAU) Always Below 1 Ω
G41-23 (SWG) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G4-13 (IL+2) - Body ground Light control switch in the tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

5.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY
a.

Remove the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral with sensor cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY AND BATTERY)
a.

Disconnect the G41 navigation receiver assembly connector.


b.

Disconnect the G4 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G41-23 (SWG) - G4-3 (EAU) Always Below 1 Ω
G41-23 (SWG) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G4-13 (IL+2) - Body ground Light control switch in the tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

8.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

8.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.
E259248C23
1.51,0.396 1.896,0.594 0.385,0.198 2.333,1.75 2.167,1.75 2.167,1.75 2.073,1.344 true 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 1.573,0.417 2.125,0.635 0.552,0.219 10 false G43 2.406,1.667 2.958,1.885 0.552,0.219 10 false ILL+
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the navigation receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G43-10 (ILL+) - Body ground Light control switch in the tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G44 navigation receiver assembly connector.


b.

Disconnect the G9 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G44-5 (ILL-) - G9-21 (ILL-) Always Below 1 Ω
G44-5 (ILL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR