Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR CLOSER SYSTEM
RM33K0E _59 Vehicle Exterior _043559 DOOR / HATCH _0219589 BACK DOOR CLOSER SYSTEM U

DOOR / HATCH  BACK DOOR CLOSER SYSTEM  TERMINALS OF ECU  


CHECK MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door System)


NOTICE:

If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION


a.

Disconnect the V12 and V13 multiplex network door ECU connectors.

C278778N09
2.417,0.531 2.833,0.781 0.417,0.25 4.302,0.51 4.719,0.76 0.417,0.25 2.51,0.594 2.969,0.792 0.458,0.198 10 false V13 4.406,0.573 4.865,0.771 0.458,0.198 10 false V12


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V12-1 (ECUB) - Body ground W - Body ground Battery power supply Always 11 to 14 V
V12-7 (IG) - Body ground V - Body ground IG power supply Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
V13-8 (B) - Body ground G - Body ground Battery power supply Always 11 to 14 V
V13-7 (GND) - Body ground W-B - Body ground Body ground Always Below 1 Ω


c.

Reconnect the V12 and V13 multiplex network door ECU connectors.


d.

Measure the voltage and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V13-10 (DC+) - V13-9 (DC-) B - R Back door lock assembly (back door lock motor) circuit Back door lock motor operating 11 to 14 V
Back door lock motor not operating Below 1 V
V12-6 (PAWL) - Body ground V - Body ground Back door lock assembly pawl switch signal circuit Back door fully open → Partially close → Back door fully close → Power back door operatestop Below 1 V → 11 to 14 V → 11 to 14 V → Below 1 V
V12-20 (FUL) - Body ground W - Body ground Back door lock assembly (back door courtesy switch) signal circuit Back door closed → open Pulse generation → Below 1 V
V12-24 (HAF) - Body ground G - Body ground Back door lock assembly (half latch switch) signal circuit Back door closed → fully open 11 to 14 V → Below 1 V
V12-21 (POS) - Body ground GR - Body ground Back door lock assembly (initial switch) signal circuit Back door open → Back door closer operates → Back door closed Below 1 V → 11 to 14 V → Below 1 V



CHECK MULTIPLEX NETWORK DOOR ECU (w/o Power Back Door System)


a.

Disconnect the V25 and V26 multiplex network door ECU connectors.

C278778E09
2.417,0.531 2.833,0.781 0.417,0.25 4.302,0.51 4.719,0.76 0.417,0.25 2.51,0.594 2.969,0.792 0.458,0.198 10 false V26 4.406,0.573 4.865,0.771 0.458,0.198 10 false V25


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V25-1 (ECUB) - Body ground W - Body ground Battery power supply Always 11 to 14 V
V25-7 (IG) - Body ground V - Body ground IG power supply Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
V26-8 (B) - Body ground G - Body ground Battery power supply Always 11 to 14 V
V26-7 (GND) - Body ground W-B - Body ground Body ground Always Below 1 Ω


c.

Reconnect the V25 and V26 multiplex network door ECU connectors.


d.

Measure the voltage and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V26-10 (DC+) - V26-9 (DC-) B - R Back door lock assembly (back door lock motor) circuit Back door lock motor operating 11 to 14 V
Back door lock motor not operating Below 1 V
V25-6 (PAWL) - Body ground V - Body ground Back door lock assembly pawl switch signal circuit Back door fully open → Partially close → Back door fully close → Power back door operatestop Below 1 V → 11 to 14 V → 11 to 14 V → Below 1 V
V25-20 (FUL) - Body ground W - Body ground Back door lock assembly (back door courtesy switch) signal circuit Back door closed → open Pulse generation → Below 1 V
V25-24 (HAF) - Body ground G - Body ground Back door lock assembly (half latch switch) signal circuit Back door closed → fully open 11 to 14 V → Below 1 V
V25-21 (POS) - Body ground GR - Body ground Back door lock assembly (initial switch) signal circuit Back door open → Back door closer operates → Back door closed Below 1 V → 11 to 14 V → Below 1 V



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


a.

Disconnect the G16 certification ECU (smart key ECU assembly) connector.

B333750N07
2.427,0.281 2.865,0.563 0.438,0.281 4.094,0.292 4.531,0.573 0.438,0.281 2.521,0.323 2.979,0.521 0.458,0.198 10 false G16 4.177,0.344 4.635,0.542 0.458,0.198 10 false G17


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G16-1 (+B) - Body ground P - Body ground Battery power supply Always 11 to 14 V
G16-10 (E) - Body ground BR - Body ground Body ground Always Below 1 Ω


c.

Reconnect the G16 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G16-14 (TSW5) - G16-10 (E) V - BR Back door opener switch assembly signal Back door opener switch assembly (open switch) off → on 4.5 V or higher → Below 1.5 V