CHECK MULTIPLEX NETWORK DOOR ECU
If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION
Disconnect the V12 and V13 multiplex network door ECU connectors.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| V12-1 (ECUB) - Body ground | W - Body ground | Battery power supply | Always | 11 to 14 V |
| V12-7 (IG) - Body ground | V - Body ground | IG power supply | Engine switch on (IG) | 11 to 14 V |
| Engine switch off | Below 1 V | |||
| V13-8 (B) - Body ground | G - Body ground | Battery power supply | Always | 11 to 14 V |
| V13-7 (GND) - Body ground | W-B - Body ground | Body ground | Always | Below 1 Ω |
Reconnect the V12 and V13 multiplex network door ECU connectors.
Measure the voltage and waveform according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| V13-10 (DC+) - V13-9 (DC-) | B - R | Back door lock assembly (back door lock motor) circuit | Back door lock motor operating | 11 to 14 V |
| Back door lock motor not operating | Below 1 V | |||
| V12-4 (BDDN) - Body ground | LG - Body ground | Back door control switch signal | Back door control switch on | Below 1 V |
| Back door control switch off | Pulse generation | |||
| V12-19 (MSW) - Body ground | G - Body ground | Power back door main switch signal | Power back door main switch on | Below 1 V |
| Power back door main switch off | Pulse generation | |||
| V12-8 (PBDS) - Body ground | R - Body ground | Door control switch assembly signal | Door control switch assembly on | Below 1 V |
| Door control switch assembly off | 11 to 14 V | |||
| V12-5 (BZR+) - Body ground | V - Body ground | Wireless door lock buzzer signal | Power back door warning buzzer sounding | Pulse generation |
| Power back door warning buzzer not sounding | Below 1 V | |||
| V12-18 (OSL) - V12-17 (OSE) | L - GR | Power back door sensor assembly LH signal | Power back door sensor assembly LH not pressed | 4 to 6 V |
| Power back door sensor assembly LH pressed | Below 1 V | |||
| V12-16 (OSR) - V12-17 (OSE) | SB - GR | Power back door sensor assembly RH signal | Power back door sensor assembly RH not pressed | 4 to 6 V |
| Power back door sensor assembly RH pressed | Below 1 V |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Disconnect the G16 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G16-1 (+B) - Body ground | P - Body ground | Battery power supply | Always | 11 to 14 V |
| G16-10 (E) - Body ground | BR - Body ground | Body ground | Always | Below 1 Ω |
Reconnect the G16 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G16-14 (TSW5) - G16-10 (E) | V - BR | Back door opener switch assembly signal | Back door opener switch assembly (open switch) off → on | 4.5 V or higher → Below 1.5 V |