Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › IGNITION SYSTEM
RM33K0E _51 Engine / Hybrid System _043567 2TR-FE ENGINE CONTROL _0220943 IGNITION SYSTEM G

2TR-FE ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A343690

To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.


PROCEDURE

Hide 1.PERFORM SPARK TEST

CAUTION:

To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.


a.

Check for DTCs.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

If a DTC is output, perform troubleshooting procedures for that DTC.



b.

Check if sparks occur.

i.

Remove the 4 ignition coil assemblies and 4 spark plugs.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL


ii.

Disconnect the 4 injector connectors.


iii.

Install the spark plug to the ignition coil assembly and connect the ignition coil connector.


iv.

Ground the spark plug.


v.

Visually check that sparks occur while the engine is being cranked.

NOTICE:
·

When performing the inspection, be sure to ground the hexagonal portion or the threaded portion of the spark plug.

·

Do not crank the engine for more than 2 seconds.

·

If an ignition coil assembly is struck or dropped, replace it with a new one.

·

If a spark plug is struck or dropped, replace it with a new one.





Hide 2.PERFORM IGNITION COIL AND SPARK TEST

HINT:

Perform "Inspection After Repair" after replacing a spark plug or ignition coil assembly.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Spark test procedure.

i.

Check that the wire harness side connector of the ignition coil assembly is securely connected.

Result:
Result Proceed to
NG Connect securely
OK Go to next step



ii.

Perform a spark test on the malfunctioning ignition coil assembly.

1.

Replace the ignition coil assembly with a normal one.

2.

Perform the spark test again.


Result:
Result Proceed to
OK Replace ignition coil assembly
NG Go to next step



iii.

Inspect the spark plug.

1.

If there is a cylinder in which ignition does not occur, interchange the spark plug of that cylinder and the spark plug of a cylinder in which ignition properly occurs.

2.

Check that sparks occur in the cylinder in which the properly functioning spark plug was installed.


Result:
Result Proceed to
OK Replace spark plug
NG Inspect ignition system
Click here(Click here)


NOTICE:
·

If an ignition coil assembly is struck or dropped, replace it with a new one.

·

If a spark plug is struck or dropped, replace it with a new one.




iv.

Check the camshaft position sensor.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>P0340


v.

Check the crankshaft position sensor.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>P0335



b.

Connect the 4 injector connectors.


c.

Install the 4 ignition coil assemblies and 4 spark plugs.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION



Hide 19100P 3.INSPECT SPARK PLUG

NOTICE:
·

Do not use a wire brush for cleaning.

·

Do not attempt to adjust the electrode gap of a used spark plug.



HINT:

Perform "Inspection After Repair" after replacing a spark plug.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
I039522C37
1.083,1.979 0.906,2.063 0.906,2.063 0.646,2.063 false 0.448,1.938 0.646,2.135 0.198,0.198 10 false *a
*a Body Ground


Check the electrode.

i.

Using a megohmmeter, measure the insulation resistance.

Standard Insulation Resistance:
Tester Connection Condition Specified Condition
Spark plug (Terminal part) - Body ground Always 10 MΩ or higher


HINT:

If a megohmmeter is not available, perform the following simple inspection instead.




b.

Alternative inspection method:

i.

Quickly accelerate the engine to 4000 rpm 5 times.


ii.

Remove the spark plug.


iii.

Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.



c.

Check the spark plug for any damage on its threads and insulator.

If there is damage, replace the spark plug. If not, reinstall the spark plug.

Recommended Spark Plug:
Manufacturer Product
DENSO FK20HR-A8



d.

Check the spark plug electrode gap.

Maximum electrode gap for used spark plug:

1.1 mm (0.0433 in.)


If the gap is more than the maximum, replace the spark plug.

Electrode gap for new spark plug:

0.7 to 0.8 mm (0.0276 to 0.0315 in.)


NOTICE:

When adjusting the gap of a new spark plug, bend only the base of the ground electrode. Do not touch the tip. Never attempt to adjust the gap of a used plug.



e.
A301633

Clean the spark plugs.

If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

Air pressure:

588 kPa (6.0 kgf/cm2, 85 psi)


Duration:

20 seconds or less


HINT:

Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.