Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM
RM33K0E _51 Engine / Hybrid System _043567 2TR-FE ENGINE CONTROL _0221972 SFI SYSTEM J

2TR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, the ST NO.1 relay drive signal output from the ignition switch assembly is input into the STA terminal of the ECM, and the NE signal generated by the crankshaft position sensor is also input into the NE+ terminal. The ECM interprets that the engine is cranked, and turns transistor Tr1 in the ECM internal circuit on. Current flows to the C/OPN NO.1 relay by turning Tr1 on. Then, the fuel pump operates.

While the NE signal is input into the ECM with the engine running, the ECM turns Tr1 on continuously.


WIRING DIAGRAM

A357152E03
5.979,1.49 6.594,1.688 0.615,0.198 10 false MREL 5.625,1.5 6.083,1.698 0.458,0.198 10 false G56 5.781,1.323 5.938,1.521 0.156,0.198 10 false 6 5.188,1.5 5.5,1.698 0.313,0.198 10 false 2P 5.281,1.313 5.438,1.51 0.156,0.198 10 false 9 4.802,2.156 5.406,2.479 0.604,0.323 10 false EFI-MAIN NO. 1 3.563,0.698 5.25,0.896 1.688,0.198 10 false EFI-MAIN NO. 1 3.563,1.177 4.635,1.375 1.073,0.198 10 false AM2 NO. 2 3.031,0.563 3.344,0.76 0.313,0.198 10 false 2B 3.031,0.365 3.188,0.563 0.156,0.198 10 false 1 3.021,2.26 3.333,2.458 0.313,0.198 10 false 2G 3.031,2.083 3.188,2.281 0.156,0.198 10 false 6 0.75,0.698 1.521,0.896 0.771,0.198 10 false J/B-B 1.417,3.313 1.573,3.51 0.156,0.198 10 false 5 2.198,3.333 2.354,3.531 0.156,0.198 10 false 3 1.406,3.792 1.563,3.99 0.156,0.198 10 false 1 2.188,3.802 2.344,4 0.156,0.198 10 false 2 1.646,4.177 2.104,4.375 0.458,0.198 10 false IG2*2 1.146,4.635 2.667,5.49 1.521,0.854 10 false Certification ECU (Smart Key ECU Assembly)*2 1.135,4.448 1.594,4.646 0.458,0.198 10 false G16 0.802,4.333 1.115,4.531 0.313,0.198 10 false 20 0.625,4.531 1.24,4.729 0.615,0.198 10 false IG1D 3.031,3.417 3.344,3.615 0.313,0.198 10 false 2G 3.021,3.24 3.177,3.438 0.156,0.198 10 false 1 3.563,4.052 5.094,4.25 1.531,0.198 10 false C/OPN NO. 1 4.49,4.771 4.802,4.969 0.313,0.198 10 false 2K 4.292,4.781 4.448,4.979 0.156,0.198 10 false 5 5,4.781 5.313,4.979 0.313,0.198 10 false 2P 5.281,4.771 5.438,4.969 0.156,0.198 10 false 8 5.979,5.375 6.292,5.573 0.313,0.198 10 false FC 5.625,5.469 6.083,5.667 0.458,0.198 10 false G56 5.771,5.26 5.927,5.458 0.156,0.198 10 false 5 2.979,5 4.656,5.542 1.677,0.542 10 false Instrument Panel Junction Block Assembly 3.052,2.76 3.365,2.958 0.313,0.198 10 false 2J 3.021,2.573 3.177,2.771 0.156,0.198 10 false 5 1.552,5.875 2.01,6.094 0.458,0.219 10 false G133 1.552,6.042 5.219,6.24 3.667,0.198 10 false Ignition Switch Assembly*1 0.333,5.75 1.51,6.156 1.177,0.406 10 false STRG LOCK/AM2 NO. 1 0.375,6.844 1.448,7.042 1.073,0.198 10 false FL MAIN 0.479,8.094 1.552,8.292 1.073,0.198 10 false Battery 1.594,7.865 2.969,8.063 1.375,0.198 10 false Fuel Pump 1.594,7.708 1.906,7.906 0.313,0.198 10 false O6 1.406,7.406 1.563,7.604 0.156,0.198 10 false 4 1.448,8.292 1.604,8.49 0.156,0.198 10 false 5 5.99,6.969 6.448,7.167 0.458,0.198 10 false NE+ 5.979,7.396 6.438,7.594 0.458,0.198 10 false STA 4.667,6.979 6.042,7.177 1.375,0.198 10 false NE Signal 5.719,6.792 6.031,6.99 0.313,0.198 10 false 27 5.75,7.219 6.063,7.417 0.313,0.198 10 false 17 4.594,7.417 6.125,7.615 1.531,0.198 10 false STA Signal 5.635,6.979 6.094,7.177 0.458,0.198 10 false C14 5.635,7.417 6.094,7.615 0.458,0.198 10 false C15 2.719,7.875 7.156,8.073 4.438,0.198 10 false *1: w/o Entry and Start System 2.719,8.281 7,8.479 4.281,0.198 10 false *2: w/ Entry and Start System 4.677,3.281 5.906,3.479 1.229,0.198 10 false IG2 NO. 1 1.448,5.479 1.604,5.677 0.156,0.198 10 false 4 2.563,5.5 2.719,5.698 0.156,0.198 10 false 3 1.594,5.479 2.052,5.677 0.458,0.198 10 false AM2 2.26,5.49 2.719,5.688 0.458,0.198 10 false IG2 6.323,8.042 6.781,8.24 0.458,0.198 10 false ECM 2.438,3.344 2.75,3.542 0.313,0.198 10 false *2 2.75,4.156 3.063,4.354 0.313,0.198 10 false *1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.

Result:
Result Proceed to
Fuel pump operating sound does not occur
(w/o Entry and Start System)
A
Fuel pump operating sound does not occur
(w/ Entry and Start System)
B
Fuel pump operating sound occurs C




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF C/OPN NO. 1 RELAY)

B

3.INSPECT C/OPN NO. 1 RELAY

C

9.READ VALUE USING GTS (STARTER SIGNAL)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF C/OPN NO. 1 RELAY)
a.
A348512C01
0.271,0.969 0.625,1.24 0.354,0.271 0.344,1.021 0.656,1.219 0.313,0.198 10 false 2G 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the instrument panel junction block assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2G-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT C/OPN NO. 1 RELAY

NG

8.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
3.INSPECT C/OPN NO. 1 RELAY

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECM)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECM)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2P-8 - G56-5 (FC) Always Below 1 Ω
2P-8 or G56-5 (FC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FUEL PUMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FUEL PUMP)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Disconnect the fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2K-5 - O6-4 Always Below 1 Ω
2K-5 or O6-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)
a.

Disconnect the fuel pump connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O6-5 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FUEL PUMP
a.

Inspect fuel pump.

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Result Proceed to
OK A
NG B



A

B

8.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the ignition switch assembly connector.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G133-3 (IG2) - 2G-1 Always Below 1 Ω
G133-3 (IG2) or 2G-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the result when the ignition switch is ON and the engine starts.

OK:
Condition Starter Signal
Ignition switch ON OFF
Engine Started ON



Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (ENGINE SPEED)

NG

10.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 234 9

e.

Read the values displayed on the GTS while cranking.

OK:

Values are displayed continuously.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

CHECK CRANKSHAFT POSITION SENSOR CIRCUIT