Home › Drivetrain › AC60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)
RM33K0E _52 Drivetrain _043526 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0221983 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) L

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  PRECAUTION  


PRECAUTION


NOTICE:
·

When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

Perform the Reset Memory procedures (A/T initialization) after replacing the automatic transmission assembly, transmission valve body assembly or any of the shift solenoid valves.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)>INITIALIZATION

HINT:

Reset Memory cannot be completed by only reconnecting the cable to the negative (-) battery terminal.


·

If either of the following conditions is met, perform ATF Thermal Degradation Estimate Reset.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)>INITIALIZATION

·

The ATF has been replaced.

·

Approximately 50% or more of the ATF has been replaced during a repair of the transmission or a similar operation.


·

Perform Registration (VIN registration) when replacing the ECM.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>REGISTRATION



CAUTION:

When using compressed air, always aim away from yourself to prevent Automatic Transmission Fluid (ATF) or kerosene from spraying on your face.


NOTICE:
·

The automatic transmission is composed of precision-made parts, necessitating careful inspection before reassembly because even a small nick could cause fluid leakage or affect performance.

·

The procedures are organized so that you work on only one component group at a time. This will help avoid confusion with similar-looking parts of different sub-assemblies being on your workbench at the same time.

·

The component groups are inspected and repaired from the converter housing side.

·

Whenever possible, complete the inspection, repair and reassembly before proceeding to the next component group. If a defect is found in a certain component group during reassembly, inspect and repair this group immediately. If a component group cannot be assembled because parts are being ordered, be sure to keep all parts of the group in a separate container while proceeding with disassembly, inspection, repair and reassembly of other component groups.

·

Use of Toyota Genuine ATF WS is recommended.

·

All disassembled parts should be washed clean, and compressed air should be blown through any fluid passages and holes.

·

Dry all parts with compressed air. Never use cloth.

·

The recommended ATF or kerosene should be used for cleaning.

·

After cleaning, the parts should be arranged in the order they were removed for efficient inspection, repairs and reassembly.

·

New discs for the brakes and clutches that will be used for replacement must be soaked in ATF for at least 15 minutes before reassembly.

·

All oil seal rings, clutch discs, clutch plates, rotating parts and sliding surfaces should be coated with ATF prior to reassembly.

·

All old gaskets and rubber O-rings must be replaced.

·

Do not apply adhesive cement to gaskets and similar parts.

·

Make sure that the ends of the snap rings are not aligned with any cutouts. Also make sure that snap rings are correctly installed into the grooves.

·

If a worn bushing is to be replaced, the sub-assembly containing the bushing must also be replaced.

·

Check the thrust bearings and races for wear or damage. Replace them if necessary.

·

Use petroleum jelly to keep parts in place.

·

When working with FIPG material, the following must be observed:

·

Using a razor blade and a gasket scraper, remove all the old packing (FIPG) material from the gasket surface.

·

Thoroughly clean all components to remove any loose material.

·

Clean both sealing surfaces with a non-residue solvent.

·

Parts must be reassembled within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.