Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM33K0E _51 Engine / Hybrid System _043565 1GR-FE ENGINE CONTROL _0222009 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor Circuit  P0342  Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)  P0343  Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)  P0345  Camshaft Position Sensor "A" Circuit (Bank 2)  P0347  Camshaft Position Sensor "A" Circuit Low Input (Bank 2)  P0348  Camshaft Position Sensor "A" Circuit High Input (Bank 2)  


DESCRIPTION

The VVT sensor (for intake camshaft) (VV1, VV2 signal) consists of a magnet and MRE (Magneto-Resistive Element).

The camshaft timing gear assembly has a sensor plate for the VVT sensor. When the intake camshaft rotates, changes occur in the air gaps between the sensor plate and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the intake camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

Then the ECM uses this data to control fuel injection duration, fuel injection timing and Variable Valve Timing (VVT) system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0340 Camshaft Position Sensor Circuit One of the following conditions is met:
·

Missing VVT sensor (for intake camshaft) signal despite crankshaft position sensor inputs normal at engine speed of 600 rpm or higher (1 trip detection logic).

·

No VVT sensor (for intake camshaft) signal to ECM at engine speed of 600 rpm or higher (1 trip detection logic).

·

No VVT sensor (for intake camshaft) signal to ECM while cranking (2 trip detection logic).


·

Open or short in VVT sensor (for intake camshaft of bank 1) circuit

·

VVT sensor (for intake camshaft of bank 1)

·

Camshaft timing gear assembly

·

Valve timing

·

ECM


Comes on DTC stored
P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) The output voltage of the VVT sensor (for intake camshaft) is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 1) circuit

·

VVT sensor (for intake camshaft of bank 1)

·

ECM


Comes on DTC stored
P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) The output voltage of the VVT sensor (for intake camshaft) is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 1) circuit

·

VVT sensor (for intake camshaft of bank 1)

·

ECM


Comes on DTC stored
P0345 Camshaft Position Sensor "A" Circuit (Bank 2) No VVT sensor (for intake camshaft) signal at engine speed of 600 rpm or higher (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 2) circuit

·

VVT sensor (for intake camshaft of bank 2)

·

Camshaft timing gear assembly

·

Valve timing

·

ECM


Comes on DTC stored
P0347 Camshaft Position Sensor "A" Circuit Low Input (Bank 2) The output voltage of the VVT sensor (for intake camshaft) is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 2) circuit

·

VVT sensor (for intake camshaft of bank 2)

·

ECM


Comes on DTC stored
P0348 Camshaft Position Sensor "A" Circuit High Input (Bank 2) The output voltage of the VVT sensor (for intake camshaft) is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 2) circuit

·

VVT sensor (for intake camshaft of bank 2)

·

ECM


Comes on DTC stored

HINT:

Reference: Inspection using an oscilloscope.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>P0335


MONITOR DESCRIPTION

If no pulse signal is transmitted by the VVT sensor (for intake camshaft) despite the camshaft rotating, or if the rotation of the intake camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

Also, when the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds or more, the ECM stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) VVT sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more.

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0340, P0342, P0343, P0345, P0347 or P0348.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A358820E02
0.333,2.25 0.792,2.448 0.458,0.198 10 false C129 0.354,2.417 3.083,2.635 2.729,0.219 10 false VVT Sensor (for Intake Camshaft of Bank 1) 1.5,1.917 1.958,2.115 0.458,0.198 10 false VVR- 1.417,1.385 1.875,1.583 0.458,0.198 10 false VVR+ 1.583,0.833 1.833,1 0.25,0.167 10 false VC 2.042,0.833 2.167,1 0.125,0.167 10 false 3 2.042,1.417 2.167,1.583 0.125,0.167 10 false 1 2.042,1.917 2.5,2.115 0.458,0.198 10 false 2 1.5,3.802 1.958,4 0.458,0.198 10 false VVL+ 1.5,4.333 1.958,4.531 0.458,0.198 10 false VVL- 0.333,4.635 0.792,4.833 0.458,0.198 10 false C128 0.333,4.833 3.042,5.031 2.708,0.198 10 false VVT Sensor (for Intake Camshaft of Bank 2) 4.458,0.833 4.917,1.031 0.458,0.198 10 false 12 4.792,0.833 5.25,1.031 0.458,0.198 10 false VCV1 4.458,1.385 4.917,1.583 0.458,0.198 10 false 10 4.792,1.385 5.25,1.583 0.458,0.198 10 false VV1+ 4.458,1.917 4.917,2.115 0.458,0.198 10 false 11 4.792,1.917 5.25,2.115 0.458,0.198 10 false VV1- 4.542,3.25 4.75,3.5 0.208,0.25 10 false 6 4.792,3.25 5.25,3.448 0.458,0.198 10 false VCV2 4.542,3.802 4.75,4 0.208,0.198 10 false 4 4.792,3.802 5.25,4 0.458,0.198 10 false VV2+ 4.542,4.333 4.667,4.5 0.125,0.167 10 false 5 4.792,4.333 5.25,4.531 0.458,0.198 10 false VV2- 5.333,5.219 5.792,5.417 0.458,0.198 10 false C120 5.333,5.417 5.792,5.615 0.458,0.198 10 false ECM 2,3.25 2.125,3.417 0.125,0.167 10 false 3 2,3.802 2.125,3.969 0.125,0.167 10 false 1 2,4.333 2.458,4.531 0.458,0.198 10 false 2 1.583,3.25 1.833,3.417 0.25,0.167 10 false VC

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VVT SENSOR (FOR INTAKE CAMSHAFT))
A345512C09
0.156,1.906 0.667,2.167 0.51,0.26 0.167,2.333 0.667,2.583 0.5,0.25 1.979,2.531 2.448,2.958 false 0.25,1.969 0.708,2.167 0.458,0.198 10 false C129 0.25,2.385 0.708,2.583 0.458,0.198 10 false C128 0.75,1.958 0.969,2.146 0.219,0.188 10 false *b 0.75,2.365 0.958,2.563 0.208,0.198 10 false *c 0.26,0.188 0.719,0.385 0.458,0.198 10 false *a 2.469,2.99 2.927,3.188 0.458,0.198 10 false VC
*a Front view of wire harness connector
(to VVT Sensor (for Intake Camshaft))
*b Bank 1
*c Bank 2


a.

Disconnect the VVT sensor (for intake camshaft) connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C129-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.5 V
C128-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)

NG

10.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the VVT sensor (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C129-1 (VVR+) - C120-10 (VV1+) Always Below 1 Ω
C129-2 (VVR-) - C120-11 (VV1-) Always Below 1 Ω
C128-1 (VVL+) - C120-4 (VV2+) Always Below 1 Ω
C128-2 (VVL-) - C120-5 (VV2-) Always Below 1 Ω
C129-1 (VVR+) or C120-10 (VV1+) - Body ground and other terminals Always 10 kΩ or higher
C129-2 (VVR-) or C120-11 (VV1-) - Body ground and other terminals Always 10 kΩ or higher
C128-1 (VVL+) or C120-4 (VV2+) - Body ground and other terminals Always 10 kΩ or higher
C128-2 (VVL-) or C120-5 (VV2-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR INTAKE CAMSHAFT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (VVT SENSOR (FOR INTAKE CAMSHAFT))
A316078C01
2.469,0.604 2.781,0.76 0.313,0.156 10 false *a 0.448,2.646 0.76,2.844 0.313,0.198 10 false OK 0.479,0.635 0.792,0.833 0.313,0.198 10 false NG
*a Clearance


a.

Check the VVT sensor (for intake camshaft) installation.

OK:

VVT sensor (for intake camshaft) is installed correctly.



Result:
Proceed to
OK
NG



OK

4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF SENSOR PLATE)

NG

SECURELY REINSTALL VVT SENSOR (FOR INTAKE CAMSHAFT)

4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF SENSOR PLATE)
a.

Inspect the teeth of the sensor plate.

OK:

Sensor plate teeth do not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
a.

Remove the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.

Click hereEngine / Hybrid System>1GR-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL


b.
A297269

Turn the crankshaft pulley, and align its groove with the "0" timing mark of the timing chain cover.


c.
A346187C03
0.813,0.708 2.854,0.229 2.854,0.229 2.552,0.688 true 0.802,1.104 1.75,1.854 1.75,1.854 2.573,1.198 true 1.052,3.052 2.885,2.604 2.885,2.604 2.542,3.063 true 0.99,3.625 1.792,4.313 1.792,4.313 2.573,3.5 true 0.031,0.031 0.344,0.188 0.313,0.156 10 false *A 0.063,2.281 0.375,2.438 0.313,0.156 10 false *B 2.885,0.146 3.104,0.333 0.219,0.188 10 true *a 1.656,1.865 1.865,2.063 0.208,0.198 10 true *a 2.917,2.5 3.125,2.677 0.208,0.177 10 true *a 1.708,4.323 1.938,4.51 0.229,0.188 10 true *a
*A Bank 1
*B Bank 2
*a Timing Mark


Check that the timing marks of the camshaft timing gear assemblies and camshaft timing sprockets are aligned with the timing marks of the bearing cap as shown in the illustration.

HINT:

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.


OK:

The timing marks on the camshaft timing gear assemblies and camshaft timing sprockets are aligned as shown in the illustration.


HINT:

If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.



Result:
Proceed to
OK
NG



OK

6.REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT)

NG

8.CHECK ENGINE MECHANICAL SYSTEM
6.REPLACE VVT SENSOR (FOR INTAKE CAMSHAFT)
a.

Replace the VVT sensor (for intake camshaft).

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>CAMSHAFT POSITION SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342, P0343, P0345, P0347 OR P0348)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342, P0343, P0345, P0347 OR P0348)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0340, P0342, P0343, P0345, P0347 or P0348 is output A
DTCs are not output B


HINT:

If the engine does not start, replace the ECM.




A

B

END

8.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


Result:
Proceed to
OK
NG



OK

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342, P0343, P0345, P0347 OR P0348)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342, P0343, P0345, P0347 OR P0348)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0340, P0342, P0343, P0345, P0347 or P0348 is output A
DTCs are not output B


HINT:

If the engine does not start, replace the ECM.




A

B

10.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the VVT sensor (for intake camshaft) connector.


b.

Disconnect the VVT sensor (for exhaust camshaft) connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C129-3 (VC) - C120-12 (VCV1) Always Below 1 Ω
C128-3 (VC) - C120-6 (VCV2) Always Below 1 Ω
C129-3 (VC) or C120-12 (VCV1) - Body ground and other terminals Always 10 kΩ or higher
C128-3 (VC) or C120-6 (VCV2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR