Home › Engine / Hybrid System › 1GD-FTV FUEL › FUEL INJECTOR
RM33K0E _51 Engine / Hybrid System _043571 1GD-FTV FUEL _0222049 FUEL INJECTOR G

1GD-FTV FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23670 1.INSPECT INJECTOR ASSEMBLY

a.
A379198C01
0.854,0.646 1.063,0.646 1.063,0.646 1.396,0.938 true 0.865,1.635 1.073,1.635 1.073,1.635 1.396,1.26 true 2.104,0.938 2.531,0.51 2.531,0.51 2.76,0.51 true 2.115,1.25 2.594,1.458 2.594,1.458 2.823,1.458 true 1.708,0.896 1.948,0.219 1.948,0.219 2.177,0.219 true 1.74,1.292 1.917,1.875 1.917,1.875 2.146,1.875 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 2.792,0.417 3.208,0.615 0.417,0.198 10 false GND 2.854,1.333 3.271,1.531 0.417,0.198 10 false Vout 2.167,1.833 2.583,2.031 0.417,0.198 10 false Lin 2.229,0.115 2.646,0.313 0.417,0.198 10 false Vc 0.698,0.542 1.115,0.74 0.417,0.198 10 false *b 0.708,1.531 1.125,1.729 0.417,0.198 10 false *c
*a Component without harness connected
(Injector Assembly)
*b No. 1 Injector Assembly - #1
No. 2 Injector Assembly - #2
No. 3 Injector Assembly - #3
No. 4 Injector Assembly - #4
*c No. 1 Injector Assembly - #10
No. 2 Injector Assembly - #20
No. 3 Injector Assembly - #30
No. 4 Injector Assembly - #40


for i-ART:

Inspect the injector assembly.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (GND) - 4 (Vout) 25°C (77°F) 16.4 kΩ or less
2 (VC) - 4 (Vout) 3.5 kΩ or less


If the result is not as specified, replace the injector assembly.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Item Tester Connection Condition Specified Condition
No. 1 Injector Assembly 3 (#1) - 6 (#10) 20°C (68°F) 0.52 to 0.66 Ω
No. 2 Injector Assembly 3 (#2) - 6 (#20)
No. 3 Injector Assembly 3 (#3) - 6 (#30)
No. 4 Injector Assembly 3 (#4) - 6 (#40)


HINT:

The temperature indicated in "Condition" is the temperature of the injector assembly.


If the result is not as specified, replace the injector assembly.



b.

except i-ART:

Inspect the injector assembly.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 0.52 to 0.66 Ω


HINT:

The temperature indicated in "Condition" is the temperature of the injector assembly.


If the result is not as specified, replace the injector assembly.