Home › Engine / Hybrid System › 1GD-FTV FUEL › FUEL FILTER(for Cylinder Block Side)
RM33K0E _51 Engine / Hybrid System _043571 1GD-FTV FUEL _0222053 FUEL FILTER(for Cylinder Block Side) A

1GD-FTV FUEL  FUEL FILTER(for Cylinder Block Side)  REPLACEMENT  


CAUTION / NOTICE / HINT

NOTICE:

Clean the diesel fuel filter assembly and remove dirt completely.


PROCEDURE

Hide 2.REMOVE FUEL FILTER CAP WITH ELEMENT

a.
A339634

Disconnect the crankshaft position sensor connector and remove the 2 bolts.


b.

Detach the 3 clamps and disconnect the engine wire.


c.
A339673

Remove the union bolt and gasket, disconnect the No. 4 fuel pipe sub-assembly from the fuel filter assembly.


d.
A339675

Remove the 2 fuel pipe clamps from the No. 3 fuel pipe and fuel filter assembly.

NOTICE:

Do not scratch or dent the installation surface of the No. 4 fuel pipe sub-assembly.



e.
A339635

Remove the union bolt and gasket, disconnect the No. 3 fuel pipe from the fuel filter assembly.


f.
A339637

Loosen the 4 screws.


g.
A339676

Remove the 2 nuts and disconnect the fuel filter assembly from the cylinder block sub-assembly.


h.
A339637

Remove the 4 screws and fuel filter cap with element from the fuel filter assembly.

HINT:

Use a container to catch the draining fuel.



i.
A339638

Remove the O-ring from the fuel filter assembly.


Hide 3.INSTALL FUEL FILTER CAP WITH ELEMENT

a.

Apply a light coat of diesel fuel to a new O-ring.


b.

Install the O-ring to the fuel filter assembly.


c.

Temporarily install a new fuel filter element with cap to the fuel filter assembly with the 4 screws.


d.
A362715N01
0.75,3.146 0.958,3.333 0.208,0.188 10 false 1 0.74,2.031 0.938,2.24 0.198,0.208 10 false 3 2.615,2.031 2.813,2.24 0.198,0.208 10 false 2 2.594,3.167 2.813,3.375 0.219,0.208 10 false 4

Tighten the 4 screws in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Check the torque of screw 1 after tightening screw 4.



e.

Connect the fuel filter assembly with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


f.

Install the No. 3 fuel pipe and a new gasket to the fuel filter assembly with the union bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


g.
A339639C02
1.792,3.063 2.229,2.771 2.229,2.771 2.365,2.771 true 2.417,2.688 2.667,2.865 0.25,0.177 10 true *a 1.427,2.573 1.667,2.771 0.24,0.198 10 true *b 1.823,2.583 2.063,2.781 0.24,0.198 10 true *b
*a Paint Mark
*b 0 to 2 mm (0 to 0.0787 in.)


Install the 2 fuel pipe clamps to the fuel filter assembly and No. 3 fuel pipe.

NOTICE:

Be careful that the fuel pipe clamp and No. 4 fuel pipe sub-assembly do not interfere with each other.


HINT:

Make sure the fuel pipe clamp is oriented as shown in the illustration.



h.

Install the No. 4 fuel pipe sub-assembly and a new gasket to the fuel filter assembly with the union bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


i.
A339634N01
2.958,0.51 3.135,0.688 0.177,0.177 10 true A 1.865,0.094 2.073,0.292 0.208,0.198 10 true B

Connect the crankshaft position sensor connector.


j.

Attach the 3 clamps and connect the engine wire with the 2 bolts.

Torque:
for bolt A : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
for bolt B : 18.5 N*m (189 kgf*cm, 14 ft.*lbf)