Home › Engine / Hybrid System › 1GD-FTV INTAKE / EXHAUST › INTAKE MANIFOLD
RM33K0E _51 Engine / Hybrid System _043577 1GD-FTV INTAKE / EXHAUST _0222057 INTAKE MANIFOLD A

1GD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
·

Injector assembly (including shuffling the injector assemblies between the cylinders)

·

Common rail assembly

·

Cylinder head sub-assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


·

Supply pump assembly

·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


Fuel inlet pipe sub-assembly

·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.



PROCEDURE

Hide 17111 1.INSTALL INTAKE MANIFOLD

a.
A345106C01
2.75,0.385 2.979,0.385 2.979,0.385 3.24,0.781 true 2.573,0.281 2.885,0.438 0.313,0.156 10 true *a
*a Protrusion


Install a new gasket to the cylinder head sub-assembly.

HINT:

Install the gasket with the protrusion the rear side of the vehicle as shown in the illustration.



b.

Temporarily install the intake manifold with the 7 bolts and 2 nuts.


c.
A359574C03
0.073,2.542 0.385,2.74 0.313,0.198 10 true *b 0.063,0.052 0.375,0.25 0.313,0.198 10 true *a
*a w/ Swirl Control Valve
*b w/o Swirl Control Valve
V100135

Bolt
V100136

Nut


Tighten the 7 bolts and 2 nuts in the order shown in the illustration.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


d.

w/o Swirl Control Valve:

Connect the vacuum hose assembly to the vacuum transmitting pipe sub-assembly.


e.

Connect the wire harness bracket with the bolt.

Torque:
18.6 N*m (190 kgf*cm, 14 ft.*lbf)


Hide 25804 2.INSTALL VACUUM CONTROL VALVE SET (for Swirl Control Valve)

a.

Install the vacuum control valve set with bolt to the cylinder head sub-assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the 2 vacuum hoses to the vacuum control valve set and vacuum transmitting pipe sub-assembly.


c.

Connect the wire harness clamp and vacuum control valve set connector.


Hide 23770 3.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

a.

Install the No. 2 nozzle leakage pipe assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 6 fuel hose to the No. 3 nozzle leakage pipe assembly and slide the clamp to secure the hoses.


c.

Install the No. 4 fuel hose and No. 5 fuel hose to the No. 2 nozzle leakage pipe assembly, and slide the 4 clamps to secure the hose.


Hide 23804C 4.INSTALL FUEL INLET PIPE SUB-ASSEMBLY

NOTICE:

When replacing the fuel supply pump assembly, it is necessary to replace the fuel inlet pipe sub-assembly, No. 1 injection pipe clamp and No. 2 injection pipe clamp with a new one.

Keep the fuel inlet pipe sub-assembly free of foreign matter.


a.

Temporarily install the fuel inlet pipe sub-assembly.


b.

Install new No. 1 injection pipe clamp and No. 2 injection pipe clamp with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.
A375573N01
1.479,1.104 1.479,0.938 1.479,0.938 1.292,0.844 false 1.354,1.125 1.813,1.323 0.458,0.198 10 true SST

Using SST, tighten the fuel inlet pipe sub-assembly union nut on the common rail side sub-assembly.

SST
09245-11010  

Torque:
Specified tightening torque : 40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

·

When using a union nut wrench (fulcrum length of 50 mm (1.97 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 31 N*m (316 kgf*cm, 23 ft.*lbf)




d.
A329093C06
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 19 mm union nut wrench, tighten the fuel inlet pipe sub-assembly union nut on the fuel supply pump assembly side.

Torque:
Specified tightening torque : 48 N*m (489 kgf*cm, 35 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 41 N*m (418 kgf*cm, 30 ft.*lbf)




Hide 17118 5.INSTALL MANIFOLD STAY

a.

Install the manifold stay with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Install the wiring harness clamp bracket with the bolt.

Torque:
12.6 N*m (128 kgf*cm, 9 ft.*lbf)


Hide 23815D 6.INSTALL NO. 3 FUEL PIPE (w/ Pressurized Fuel Filter)

a.

Temporarily install the No. 3 fuel pipe and 2 new gaskets with the union bolt and supply pump hollow screw.


b.

Tighten the union bolt and supply pump hollow screw.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

Install the 2 fuel pipe clamps to the No. 3 fuel pipe and fuel filter.


Hide 23804D 7.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF)

a.

Temporarily install the No. 4 fuel pipe sub-assembly and 2 new gaskets with the 2 union bolts and bolt.


b.
A356214C03
2.521,3 2.719,3.198 0.198,0.198 10 true 1 2.969,3 3.156,3.188 0.188,0.188 10 true 2 1.375,1.677 1.573,1.875 0.198,0.198 10 true 3
V100136

Union Bolt
V100137

Bolt


Tighten the 2 union bolts and bolts in the order shown in the illustration.

Torque:
union bolt : 42 N*m (428 kgf*cm, 31 ft.*lbf)
bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the No. 4 fuel pipe sub-assembly to the No. 1 fuel pipe.

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL SYSTEM>PRECAUTION


Hide 8.INSTALL WIRING HARNESS CLAMP BRACKET

a.

Install the wiring harness clamp bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Attach the 2 wire harness clamps.


c.

Connect the diesel throttle body assembly connector and pre-stroke control valve connector.


Hide 23812D 9.INSTALL NO. 2 FUEL PIPE

a.

Connect the No. 2 fuel pipe and with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11409 10.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the engine oil level dipstick guide.


c.

Install the engine oil level dipstick guide with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Connect the vacuum hose to the intake manifold.


e.

Install the engine oil level dipstick.


Hide 25800 11.INSTALL EGR COOLER SUB-ASSEMBLY AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 12.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

(Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)