Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM
RM33K0E _51 Engine / Hybrid System _043566 1KD-FTV ENGINE CONTROL _0222113 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch to ON.
(b) Brake pedal is released.
(c) The STP signal is off when the ST1- signal is off, or the STP signal is on when the ST1- signal is on.
·

Open or short in stop light switch signal circuit

·

STOP fuse

·

IGN fuse

·

Stop light switch

·

ECM


- DTC stored

Related Data List
DTC No. Data List
P0504 Stop Light Switch

CONFIRMATION DRIVING PATTERN

P0504
DTC Detection Drive Pattern Depress and release brake pedal with ignition switch to ON

WIRING DIAGRAM

A377762E01
0.625,4.875 1.698,5.073 1.073,0.198 10 false Battery 0.448,4.115 1.521,4.313 1.073,0.198 10 false FL MAIN 3.0W 1.448,3.594 1.833,3.781 0.385,0.188 10 false ALT 2.938,3.583 3.396,3.771 0.458,0.188 10 false STOP 1.958,2.854 3.24,3.031 1.281,0.177 10 false Ignition Switch*2 1.958,2.688 2.344,2.875 0.385,0.188 10 false G133 2,2.25 2.385,2.438 0.385,0.188 10 false AM2 2.76,2.25 3.146,2.438 0.385,0.188 10 false IG2 3.073,2.24 3.458,2.427 0.385,0.188 10 false 3 1.823,2.24 2.208,2.427 0.385,0.188 10 false 4 2.031,1.25 2.417,1.438 0.385,0.188 10 false *1 3.552,1.719 3.938,1.906 0.385,0.188 10 false *1 1.354,1.646 1.74,1.833 0.385,0.188 10 false *2 2.51,0.542 2.74,0.729 0.229,0.188 10 false 2 2.49,1.01 2.719,1.198 0.229,0.188 10 false 5 3.271,0.542 3.5,0.729 0.229,0.188 10 false 1 3.281,1.031 3.51,1.219 0.229,0.188 10 false 3 4.26,0.552 4.49,0.74 0.229,0.188 10 false 20 4.563,0.625 5.094,0.802 0.531,0.177 10 false IGID 4.531,1.052 5.063,1.229 0.531,0.177 10 false G16 4.531,1.219 6.906,1.583 2.375,0.365 10 false Certification ECU (Smart Key ECU Assembly)*1 0.604,1.26 1.375,1.448 0.771,0.188 10 false AM2 NO. 2 0.448,2.24 1.219,2.427 0.771,0.188 10 false J/B-B 4.531,4.281 4.917,4.469 0.385,0.188 10 false A64 4.521,4.469 5.635,4.854 1.115,0.385 10 false Stop Light Switch Assembly 6.24,4.521 6.698,4.708 0.458,0.188 10 false ECM 4.552,3.802 5.01,3.99 0.458,0.188 10 false GND 4.552,3.406 4.75,3.594 0.198,0.188 10 false B 4.552,2.333 4.75,2.521 0.198,0.188 10 false B 5.146,3.417 5.344,3.604 0.198,0.188 10 false L 5.167,2.344 5.365,2.531 0.198,0.188 10 false L 3.729,2.458 4.49,2.646 0.76,0.188 10 false IG2 NO. 3 4.375,2.229 4.76,2.417 0.385,0.188 10 false 6 4.375,3.313 4.604,3.5 0.229,0.188 10 false 7 5.365,3.313 5.594,3.5 0.229,0.188 10 false 3 5.365,2.219 5.75,2.406 0.385,0.188 10 false 5 5.958,2.229 6.49,2.406 0.531,0.177 10 false ST1- 5.969,3.302 6.5,3.479 0.531,0.177 10 false STP 5.708,3.313 5.938,3.5 0.229,0.188 10 false 15 5.708,2.229 5.938,2.417 0.229,0.188 10 false 14 2.802,1.458 3.188,1.646 0.385,0.188 10 false IG2 6.229,4.354 6.615,4.542 0.385,0.188 10 false G129 1.677,4.552 4.094,4.75 2.417,0.198 10 false *1: w/ Smart Entry and Start System 1.698,4.844 4.115,5.042 2.417,0.198 10 false *2: w/o Smart Entry and Start System 4.375,3.677 4.604,3.865 0.229,0.188 10 false 2

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE)
a.
E270270C09
0.208,1.073 0.656,1.375 0.448,0.302 2.042,1.208 1.479,1.823 true 2.375,1.188 2.792,1.854 true 0.302,1.146 0.76,1.344 0.458,0.198 10 false A64 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 1.406,1.865 1.563,2.063 0.156,0.198 10 false B 2.781,1.896 2.938,2.094 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch)


Disconnect the stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A64-6 (B) - Body ground Always 11 to 14 V
A64-7 (B) - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the stop light switch connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY,INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in thetable below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK ECM (STP AND ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ECM (STP AND ST1- VOLTAGE)
a.
A303106C09
1.938,2.531 2.354,2.792 0.417,0.26 1.552,3.938 1.927,3.177 true 2.333,3.906 1.979,3.177 true 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 1.771,0.083 2.083,0.281 0.313,0.198 10 false *b 0.25,2.219 0.563,2.417 0.313,0.198 10 false *c 1.979,2.573 2.354,2.771 0.375,0.198 10 false G129 1.292,3.948 1.896,4.198 0.604,0.25 10 false 15 (STP) 2.271,3.948 2.896,4.198 0.625,0.25 10 false 14 (ST1-)
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Component with harness connected
(ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
G129-14 (ST1-) - Body ground Released 11 to 14 V
Depressed 0 to 3 V
G129-15 (STP) - Body ground Released 0 to 3 V
Depressed 11 to 14 V



d.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-3 (L) - G129-15 (STP) Always Below 1 Ω
A64-5 (L) - G129-14 (ST1-) Always Below 1 Ω
A64-3 (L) or G129-15 (STP) - Body ground and other terminals Always 10 kΩ or higher
A64-5 (L) or G129-14(ST1-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR